printed double fold bias tape 3d models

The hook can be printed in any material, but PETG or other strong filaments can be an advantage to ensure a long lifetime for the hook.The hook is best printed on a smooth plate, as this maximizes the adhesion between tape and hook.The model needs...

Pegboard holder for up to two rolls of duck tape

Make your own Duct Tape neck ties with this clever 3D printed clip. Print the tie clip. Unroll about three feet of duct tape and lay it face up. Cut the tape from a little past halfway on one edge to near the other side to taper the tape strip. Fold...

I remade one, a little stronger. in PLA or ABS. mon vieux boitier de double decametre etait vraiment dans un piteux etat. ...j'en ai refabrique un , un peu plus costaud. en PLA ou ABS. Print Settings Printer Brand: Creality Printer: Ender 3 ProRafts:...

It contains approximately 4 feet of tape (labeled with whole inches and graduations), 114 individual parts, a belt clip, a fold-out crank with detent, and lock for the tape. I printed it on a polyjet printer which utilized a wax-like support...

my old double decametre box was really in a sorry state. ...I remade one, a little stronger. in PLA or ABS. mon vieux boitier de double decametre etait vraiment dans un piteux etat. j'en ai refabrique un , un peu plus costaud. ... en PLA ou ABS.

Sony Revolutionizes Music on the Go with the WM-W800, a Compact and Powerful Walkman Stereo Double-Cassette Recorder. ...Released in 1984 by Sony Corporation in Tokyo, This Groundbreaking Device Packed Two Cassette Players into One Ultra-Small Package,...

This mount uses a standard double-sided adhesive pad and an innovative screw thread mechanism that creates secure and adjustable mounting. It comes with multiple pre-drilled holes to accommodate various screws, offering versatility for attachment on...

Wall shelf to hold your 3d prints

Customized version of https://www.thingiverse.com/thing:5136638 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5136638

Customized version of https://www.thingiverse.com/thing:5136638 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5136638

I tweaked the design near the sewing machine attachment, streamlining it for better performance. The connection mechanism between the two components has been switched up to a sleek V-groove system. ...Additionally, I incorporated a handy finger groove...

Customized version of https://www.thingiverse.com/thing:5136638 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5136638

R2 will probably yield a cleaner finish. ...This is thanks to its enhanced settings, specifically tailored for use with a 0.40 millimeter nozzle at a 0.20 millimeter layer height.

double-sided tape!!!no mounted!!!!!!!!!!!!!!!

Ziptie Cable holder for use with double sided tape.

Use double sided tape to mount to wall.

... utilizing the magnetic mount filament guide, substituting double-sided tape instead. ...It boasts an interior that's somewhat airy, yet its flat base enables faster printing and facilitates attachment to your printer with double-sided tape.

A Two-Part Print Solution. ...The Design Has Been Reinforced, Allowing It to Be Secured Using Double-Sided Tape, Eliminating the Need for Screws. ...Supports Are Required for a Successful Print.

Just took out the screws cause i'm gonna double side tape it on

To mount that you will need: - 1x printed adapter plate - 4x brass heated insert (M3, 4mm long, 5mm outer diameter) - https://www.aliexpress.com/item/4000232858343.html?spm=a2g0s.9042311.0.0.27424c4d2x9wzR - 4x M3x10 countersunk screw - double sided...

Image holder for double-sided adhesive tape. Use regular double-sided tape or power strips. ...Pictures should not be too heavy and the surface should be suitable for the tape.

Mechanical interface allowing non permanent attachment of a raspberry pie via double sided tape. This allows you to use your steel or aluminium RP case you already have. ...Great for increased thermal performance when compared to other 100% 3D printed...

Sanding block that works with 60x10mm double sided tape like the stuff that comes with 60x10mm bar magnets from Amazon. Never used the tape for the magnets but made this so I could use it with wet sandpaper. Print in any material at any layer...

Base is 20mmx20mm (many double sided tapes are 20mm, so perfect fit) Goal was a sturdy design which also allows easy and quick printing, that's also the reason for the slightly asymmetric design. ...Takes 20-25min to print depending on the print speeds...

Base is 20mmx20mm (many double sided tapes are 20mm, so perfect fit) Goal was a sturdy design which also allows easy and quick printing, that's also the reason for the slightly asymmetric design. ... Takes 20-25min to print depending on the print...

This is a remix of the honcho mirrors with the bolt hole filled up for installation with double-sided tape. The hole was making the mirrors brittle when used without a screw in it so i filled the hole and printed them in PETG for better layer...

... something i found a long time ago, but can't find the original corner version. ... If i find it then i will add credits for the remix. just print with 15% in any colour and use double side tape to mount them to wall or ceiling and place the led strip

... to attach a USB switcher to a 30mm tube (but it is a 2x model, so it is 60mm by default). ... You can print it at 1/2 size and slip it over a 30mm tube or pole and use a zip tie to tighten it down. Use double-sided tape to attach whatever you want.

This is an upgraded version of the lead mirrors, featuring a secure fastening system with double-sided tape for easy installation. ...To prevent brittleness and ensure stability, I plugged the bolt hole and 3D printed the mirrors using PETG, which...