printdry 3d models

I'm remixing the PrintDry Bowden Adapter by clintfisher, which I found on Thingiverse as thing:2853029. While testing this adapter, I noticed that the Bowden tube sometimes got pushed out when feeding filament through. To address this issue, I...

I bought some PrintDry air tight filament storage canisters, and they're great...but I didn't love pulling a vacuum in them with the indluced hand pump. Then I remembered that I have a vacuum sealer in my kitchen! I just needed an adapter so that I...

I bought some PrintDry air tight filament storage canisters, and they're great...but I didn't love pulling a vacuum in them with the indluced hand pump. Then I remembered that I have a vacuum sealer in my kitchen! I just needed an adapter so that...

The original clips that come with the PrintDry filament container are flimsy and prone to falling apart at the slightest touch. However, this updated design is built to last, boasting a more compact and reliable profile that can withstand even the...

I backed the PrintDry Filament Container. As they arrived, I saw that the original clip to close the container was extremely tight - so the lid is bending excessively. That's why I designed these clips - they are significantly thicker and stronger...

The PrintDry manual says to dry the desiccants at 65C for several hours and this lets the air circulate around a large number of them. I printed this in ASA to stand up to the heat. ... Slice it with 0 top shells, 0 bottom shells, and the infill...

PrintDry filament dryer box container allows you to accommodate multiple stacks for larger spools of filament. You can also add a 9.5 inch rod, but I opted for a wooden dowel instead, sanding down its sides for a precise fit. ...Ensure that your prints...

The Air Spacer sits snugly around the center seal of a PrintDry Vacuum Storage Container, holding back packaging material from jamming the seal as the vacuum is pulled. ...I prefer to stash multiple samples from Maker Box in one container with their...

this resulted in the spools falling off when printing direct from the dryer, which resulted in a couple of failed prints.These spool holders use the original aluminium spindles and fit spools with 73mm holes and up to 70mm wide.Print instructionsYou...

For reasons unknown, I keep losing the rubber feet on the bottom of my PrintDry Pro box when moving it between printers. Here's a replacement for them. I printed a set with Overture TPU, 0.3mm layer height, 2 perimeters. ...They're VERY...

This adapter is designed specifically to enable easy insertion and feeding of Dremel brand filament spools from the top shelf of the PrintDry Filament Dryer (Model FD-770). The adapter fits snugly onto the upper tray, similar to the provided PrintDry...

This is remixed from two sources: https://www.thingiverse.com/thing:2853029 and https://www.thingiverse.com/thing:4541507 The bolt length has been changed for the PrintDry 2 Pro with its double wall thickness. I have included both the slip-fit...

I needed a way to get my Coex 5lb spool to fit in the PrintDry Pro (with large spool extension). I came up with this. ...Several prototypes to get the dimensions just right.&nbsp;</p><p>Suggested&nbsp;</p><p>Material: PETG or ABS (or higher temp...

I was feeding directly out of our PrintDry Pro v2.0 and felt there was a bit more friction on the roller than I liked. After some measurements I found a set of bearings (6802-2RS) that fit the roller bar that comes with the drier. In order to space...

Others like me bough a PrintDry and thought “it would be nice to try dehydrating some fruits…” Here is you chance! Be advised: * only PETG can be used for this project as it will tolerate the temperature and is (kind of) food grade * the diameter...

PrintDry is a fantastic filament-drying tool. I ordered one unit with a large spool kit. This kit allows you to use 5KG spools. I got the dryer but the large spool add-on was back ordered for over 2 months! So I designed my own. I printed it on...

Others like me bough a PrintDry and thought “it would be nice to try dehydrating some fruits…” Here is you chance! Be advised: * only PETG can be used for this project as it will tolerate the temperature and is (kind of) food grade * the...

This model is provided by PrintDry. ...It is a plug for a PrintDry Pro that has a channel for a PTFE tube to pass through the port.

This pedestal elevates your PrinterDry by roughly sixty-four millimeters.

I recently acquired a batch of 3D Hero Wood PLA filament and discovered that my Spindale plugs wouldn't fit due to its enormous center hole. Fortunately, this one fits seamlessly and doesn't protrude so much that it obstructs the lid's closure. To...

Still a work in progress... Print Settings Printer Brand: Prusa Printer: i3 MK3 Rafts: Doesn't Matter Supports: No Resolution: 0.2mm Infill: 10% Notes: rn Post-Printing Punch through hole You will have to punch through the hole above the bearing.

75mm (Geeetech) and 33mm (Labists) spool holder for the PrintDry™ Filament Dryer. ... Remixed SCAD file to be parametric to different spool sizes, and generated my own from the modified script.

This is a mount for a standard 1/2" nylon wire gland from Amazon (https://smile.amazon.com/gp/product/B06Y5HGYK2/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1) that securely holds a 4mm PFTE tube in place, preventing movement. It utilizes four...

I designed this using Tinkercad, specifically for a filament spool holder that accommodates a hole diameter of up to 60mm. ...The original model is on the left, while my adaptation is prominently displayed on the right.

Spools are kept in place by holding them steady as they feed onto the system.

The Print Dry is rated to 71°C, but if you put a thermometer on it, you never quite get to that temperature in the print chamber. And with the cycling, I see it bounce between 55-65°C, never quite getting to the rated temp. For drying Nylon, you...

These two spools are designed specifically for Zortrax filament. ...The specifications include: * Diameter (d): 42 mm and height (h): 55 mm * Diameter (d): 56.5 mm and height (h): 67 mm A separate spool holder is available for Makerfill PLA with the...

Holes just come out the side of the container and the filament was dragging as I have my Prusa printer in an enclosure that the dryer sits on top of. Threw this together in Fusion 360 using rod n bearings I had laying around from other projects. ... ...

2 possible uses: 1) convert the original PrintDry into a PrintDry 2.0 vertical-style OR 2) convert a food dehydrator into a filament dryer Note: It's 35cm long so you'll need a large print bed. I rotated it 45 degrees to print on my Taz 6. I wanted...