print faster 3d models

Redraw - frame_section_3 Left & Right PRINT faster & Stronger Print Settings Rafts: No Supports: No Resolution: Ultra Low (Very Fast) Infill: Hollow Thick Walls (Fast) Notes: For M3D Print Right：Rotate X-90 Z90 Left ：Rotate X90 Z90

Redraw "calibration_item" by Atlas 3D for Print Faster 2mm -> 0.8mm Print Settings Rafts: No Supports: Doesn't Matter Resolution: Ultra Low (Very Fast) Infill: Hollow Thin Walls (Fastest) Notes: M3D Print(Version: 2015-08-06-v1.3.6.3) Move：X54.00...

New design to print really FAST without infill and support. 6 variants available: 3 Big and 3 Small (long, long hollow, short). You can print Big 0.2, 0.25, or 0.3 layer height. For Small 0.2, 0.25 layer height. 2 perimeters with extrusion width 0.4....

New design to print really FAST without infill and support. 6 variants available: 3 Big and 3 Small (long, long hollow, short). You can print Big 0.2, 0.25, or 0.3 layer height. For Small 0.2, 0.25 layer height. 2 perimeters with extrusion width 0.4....

i remixed a sorting tray for a ender 3s1 so it prints faster and uses less filament.

Remix of a spinning life counter, rotated for a faster print

This remix for the Ridgid Battery Holder eliminates the center hump from InfiniteCraftsman's design.Thus making the print slightly faster, and using a little less filament.

This remix for the Ridgid Battery Holder eliminates the center hump from InfiniteCraftsman's design.Thus making the print slightly faster, and using a little less filament.

Removed the inner Structures for faster printing, saves ~25% Time on 20% Infill and 0,2mm Layer. ... Also this Version is resized to match the WTC 2021 Terrain Maps.

Smoother printing, reduced print time and less print failures! See picture. Overnight production There are also stacked versions of theframe with an 0.25mm airgap between the parts. Obviously, the bottom sides won't be super beautiful, but that's...

Please use screw/handle and inset from the original https://www.thingiverse.com/thing:4655051/files I just filled in the triangular structure. ...Now prints 30% faster with less filament.

:/ I redesigned it for printing the rest of the stock part at 200% or larger to print faster as the walls are only 1.2mm thick so just 3 shells and no infill. Also the indents are shallower so there shouldn't be any missed or drooped areas if you...

:/ I redesigned it for printing the rest of the stock part at 200% or larger to print faster as the walls are only 1.2mm thick so just 3 shells and no infill. Also the indents are shallower so there shouldn't be any missed or drooped areas if you...

:/ I redesigned it for printing the rest of the stock part at 200% or larger to print faster as the walls are only 1.2mm thick so just 3 shells and no infill. Also the indents are shallower so there shouldn't be any missed or drooped areas if you...

Its a way to print the original file way faster

Super simple remix to use less plastic. ...3g vs 8g, less than half the print time.

This spool holds the same meters of filament as the original, but the printing time is shorter.I use this model mainly for storing TPU and HIPS filament in vacuum bags.In the original model, the inside of the spool cracked in the vacuum bag.Print...

This is an optimized version of “Lucy” (Australopithecus).This skull has been optimized to print in around ½ the time without any loss of quality (the original scan of the skull has many voids which drastically slows down printing time.There is also...

This Catan housing option is budget-friendly for its residents. ...It features no windows or doors, which speeds up the 3D printing process. ...Check it out here: http://www.thingiverse.com/thing:46065

I simplified the geometry of the vise base to make it print faster. These changes dropped the print time from 4:25 to 4:03 on my Ender 3. ... The picture preview might be messed up because STLs and Thingiverse both kinda suck, but roll with it, it's...

Despite all of the features, the print time should be ~4x faster than my previous design as this is very slim! I have also included a drill guide for the clear plastic front shield. I would recommend using 0.5mm thick material such as PETG for...

Despite all of the features, the print time should be ~4x faster than my previous design as this is very slim!I have also included a drill guide for the clear plastic front shield. I would recommend using 0.5mm thick material such as PETG for your...

Despite all of the features, the print time should be ~4x faster than my previous design as this is very slim! I have also included a drill guide for the clear plastic front shield. I would recommend using 0.5mm thick material such as PETG for your...

- The "35mmTall" version without spacers prints slightly faster. ... ## License - [Creative Commons Attribution 4.0 International](https://creativecommons.org/licenses/by/4.0/) (CC BY 4.0) - by thecardbazaar and Poikilos - based on [Miniatures...

Designed to use less material possible and to print in 2.5 hours printing with 0.2mm layer height Print it in tpu https://www.youtube.com/watch?v=xONnK509dqk

I noticed that the original file had the game boy logo being printed every layer under the surface. This added a lot of geometry. I removed this and it shaved 2 hours off the print time. I also filled in the bottom piece. I didn't like that it had...

Slope removed to reduce print times Card trays compacted to all fit on bottom World tiles reduce and fit nicely in place on right side of the board Token tray adjusted to fit and extra room given for exploration and trade tokens Alterations made to...

Compatible with RC3 windshield. More constant wall thicknesses, less holes, less extrusion start/stop and idle movements. Reduced weight of upper part. More flexible shield bar - easier assembly. Print instructionsUpper part prints OK with nozzle up...

I removed the (useless) arrow and also the wave pattern, as it did not really anything except for increasing print time I print it with wallcount 3, thats basically 100% infill but the 'infill' lines follow the geometry, the long way, so piece should...

time time time. ...on the right, and quickly made a little askew in a hurry and already prints;) some soft model. but enough that no one will throw. option to cut the tape does not work. I stick the scalpel to this and will be fine. ...print time 1:20h