primal 5 3d models

Attach the “12V power supply”, turn on the “switch” in the base and set the output voltage of the DC-DC step down board to ~5V (i set it to 5.15V) with a small screwdriver and the small screw on the blue potentiometer of the DC-DC step down board. I...

I highly recommend using a power bank as a power source for testing the dock instead of a charger plugged into mains voltage.Detailed assembly instructions:Print the two parts (I recommend 20+% infill, you might want to use the adaptive layer height...

fit a thicker filter, then just increase the Z height by 4-5% or so in your slicer program.By not using all the fan mounting screws, it is also possible to lead the wires through one of the holes of the fan-mounted label side inwards towards the exit...

The 2 halves of the box glue together with printed splines, while the front and rear end caps use M3 hardware threaded into M2.5 holes in the plastic. Z End Stops: The machine now has 2, one for each Z motor, and dedicated stepper drivers for...

 I ordered over a meter from Amazon: https://www.amazon.com/dp/B091578CLX?ref=ppx_yo2ov_dt_b_product_details&th=1 for ~$5.50. Not physical parts, but a step that must not be skipped.  In the Klipper printer.cfg file, change the amount of filament...

The infer housing, has 5 points along with a rubber grip to seal. A second trim helmet protects the whole of the water inlet. *I belive, lots of this components are easy to Break, i will go desing some spare , like the opne close clips from the...

For the bottom halves, i do because of the overhanging screw holes.You can try without, but the supports are small in this casePost-Printing - the photos of these steps are in the filesPrint and assemble the individual partsI designed the parts to be...

After 5 failed attempts, I decided to just build my own. This design is absolutely inspired by that make, but is created completely from scratch in OnShape design. I wanted the design to be easy to print, to need no supports, and to have (mostly)...

The lightning detector mounts to the posts with 2 M2.5 screws and it is angled to allow space for the Grove connectors underneath. (Be sure to mark the other ends of your Grove cables before assembly to identify where each plugs into the boards in...

The lengths were changed from 0.5 to 0.4. Another change was made with our circles at the bottom, which were too small because of the decreased height. We had to remake the circles using the 3 point arc tool, and this made it look closer to the...

The Demon Core was a spherical 6.2-kilogram (14 lb) subcritical mass of plutonium 89 millimetres (3.5 in) in diameter, manufactured during World War II by the United States nuclear weapon development effort, the Manhattan Project, as a fissile core...

You fine tune the tension of the spring and thereby the gear pressure against the filament later but for now I find about 4-5 half turns of the screw is good. You can use the original thumb screw instead if you like. At this point you can also...

Create your own version with these options: qr\_y=0, qr\_x=0, tag\_height=80, tag\_width=80, perimeter=-1000, corner\_radius=10, case\_thickness=1.8, hole\_r=10, hole\_y=0, hole\_x=30, per\_h=10, per\_w=3, obj=1, add\_sub=1, qr\_size=33,...

Once all the tests pass, perform a first layer calibration.Here are the steps to perform when you want to swap a mobile plate.Unload the filament.Power down the printer and remove the mobile plate.Attach the new mobile plate, and power on the...

This carriage was printed using another Icarus 1.2 carriage with Orbiter 1.5 and Trianglelab Dragon Standard Flow at the recommended print settings. But we start the guide from scratch. Notice: If your Dragon hotend has a V6 groove mount...

Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1...

http://www.thingiverse.com/apps/customizer/run?thing_id=739573\nCreated using Customizer version http://www.thingiverse.com/thing:739573\n\n \n\nInstructions Using the options:\nfont_narrow_widen = 0\nbar_style = only_bar\nlug_style =...

At first I planned to use 6 panels, so I bought a set of 4 panels and a set of 2 panels, but in the end I needed 5...

Avoid lifting and warped prints!There is a small amount of support needed - "for support enforcers only."Under the elevator shaft on the Middle Floor and Top Floor.The elevator door on the base floor.Increase the size of your “Dice Tower - Building...

But I suppose this is not necessary for at least 5-6 prints, if the battery is fresh. SOLUTIONS 1 & 2: SOLUTION 1 is a direct control of the Bluetooth Remote Shutter mounted on the printer. Extremely simple and easy to mount and no...

Examples listed below:-- https://www.amazon.com/Rannb-1-65-Inch-Metal-Drilling-Cutter/dp/B081TSR6VZ/ref=sr\_1\_2?dchild=1&keywords=hole+saw+42mm&qid=1625238036&sr=8-2--...

Please check the images to see examples of the pattern of cells as a single one facing the wrong way will cause a short circuit and risk a fire!!!5. To hold the sides together you can use the 90mm bolts and nuts to temporarily clamp them together via...

Test early, test often!1.Start by pushing all the bearings into the gears, depending on the accuracy of your printer you might need to use a pumpwrench or pliers to get the bearings to fit. 2.Push the drive_gear_motor_side onto the shaft of the...

                                                  Window not quite aligned (red) Properly aligned (no...

Note that if you're making 5 rewinders, you'll need a total of 10 badge springs. Some rubbery cover to put on DrumOuter. This needs to be somewhat grippy but not excessively so. The spool should be able to slip over the material without jumping. I...

Some of them probably arent relevant without some pretty specific custom pcb's but there should be enough room to fit in more generic electronics for use as a prop with light/sounds or your own lasertag electronics if you want. The barrel uses a...

You fine tune the tension of the spring and thereby the gear pressure against the filament later but for now I find about 4-5 half turns of the screw is good. You can use the original thumb screw instead if you like.At this point you can also install...

Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1...

Infill: 15% Parts to print: 1x body (for 2S or 3S) 1x front 1x back 64x track 64x rubber track 64x pins (try which one fits best for you) 8x small cog 4x main cog 1x inner track frame right 1x inner track frame left 2x outer track frame 2x track...

There are 5 files in the download: - An stl file of the top half - An stl file of the bottom half - A 3mf file with both halves - A 3mf file with both halves and a supports tear tab to make removal of the supports much easier. - A 3mf file with...