pre sliced 3d files

(3D printing time not included)Electronics:Digital Bird Pan Tilt Board with ESP32 and two TMS2208 v3 DriversShutter cable with 2.5mm SocketBoard mounted joystickPower Cable with Digital Bird NP Battery TerminalsTwo button Mount/Dismount switch...

Violence is never more than a heartbeat away.Keep your vehicles fueled!Stay in the fight!No support requiredResize for smaller or larger use. Designed on...

So should work for noisy 5015 3D printer fans too. Check your airflow after fitting. Features: Short venturi / velocity stack cone inlet Modal barrier to break up resonance into 8 separate modes, thus reducing peak intensity of primary fan...

I'm still new to the world of 3D printing, but I thought I'd tackle one of my favorite board game organization nightmares: Eclipse. Specifically, my first project was creating a tray for the game's ship parts. Between my expansions and the Rift...

... that they call HT (basically tritan) and is supposed to withstand temps over 100°C. Category: 3D Printer Accessories

So I replaced with petg bushings. Print instructionsCategory: 3D Printer Parts Print Settings Rafts: No Supports: No Notes: Print on end like they load in as for smoothest surface for bushing to set on. ...The flatter one should also print ok flipped...

A short bridge is required for the rail end caps. Post-Printing All holes are intentionally modeled as very tight fits and are intended to be drilled out with a 3mm bit to ensure proper fit. The threaded inserts will push waste material into the...

This information is part of "Scan The World", a non-profit initiative introduced by MyMiniFactory, which aims to create a digital archive of fully 3D printable sculptures, artworks, and landmarks from across the globe for public access. ...If you have...

This object is part of "Scan The World," a non-profit initiative introduced by MyMiniFactory through which we are creating a digital archive of fully 3D printable sculptures, artworks and landmarks from across the globe for the public to access for...

Use 2pcs M3x6mm screws to mount the original display mount part from the scale to the 3d printed part. Use 2pcs M3x10 screws to mount the strain relief:</p><figure class="image image_resized" style="width:75%;"><img...

I just like to cover all bases due to the different skill sets of makers) Print instructionsSupports: No Resolution: .2mm Infill: 10% Notes:** Refer to the notes below for helpful printing and assembly instructions. *One piece does require supports ...

I have a Raspberry Pi inside my Ender 3 with OctoPi, and I had this old tablet lying around, so I thought to put it on the 3d Printer with Printoid in order to control OctoPrint without having to turn on my computer. This tablet is pretty old and...

... Print Settings ============== Printer: HyperCube Rafts: No Supports: No Resolution: 0.2 Infill: 20% Filament: Devil Design and Spectrum PETG Notes: Don't print with PLA as some parts are very close to the heater. Category: 3D Printer Parts

I will lock away the goodies in the drawer, then lock the key to said drawer into the piece of 3d-printed plastic inside a padlock. The key to the padlock can then be put in a place that is not too close by, or easily reachable. Maybe hide the key...

... should hopefully see you through. The LCD base mod and y motor ramp weren't complete at that stage, bu they should be self explanatory. Further footage can be seen in the companion video: https://youtu.be/ag7b9jOhlPY Category: 3D Printer Parts

I later found a similar one even cheaper - less than $20 when I ordered it and the quality seems very good for the price.https://www.amazon.com/gp/product/B0CDPV3F4C/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1A tube would make this heavy so I...

To light the lamp I used: CR2032 round button cell battery holder 3mm LED Light Emitting Diodes Energizer CR2032 Lithium 3v Battery (1 Pack of 5) Print Settings Printer: HyperCube Evolution Rafts: No Supports: Yes Resolution: .2 Infill: Various...

... </strong></p> </p><div><p>May need to rotate pieces in slicer to enable the fastest print times. Add support where necessary, but shouldn't be necessary as long as parts are oriented properly on the build surface. Category: 3D Printing

UPDATE 3 (regarding Wanhao Duplicator i3/i3Plus):\nI highly recommend replacing the bearing rods and generously applying MoS2 grease to the inside radius of the original linear ball bearings for maximum quietness and lower friction.\nThe greased...

I do plan on redesigning this sometime in February or later as this was all done using Microsoft's 3D Builder and not CAD software. The gears are noisy and things need to be made with more precision but it works as well as beautifying some of the...

This 3D-printable adapter allows one with the above setup to easily swap speedlites inside their softboxes with AC (E26 / A15 base) LED bulbs, for video recording (youtube etc). **WARNING: this project involves dealing with AC 110V wiring, so do...

Scan the World is a non-profit initiative introduced by MyMiniFactory, through which we are creating a digital archive of fully 3D printable sculptures, artworks and landmarks from across the globe for the public to access for free. ...Scan the World is...

But loosing contact with one signal washer the resistance goes up to 30k and triggers. G-Code example Duet3 3d printer (Probe at x125 y125)Modify this to suite you and use on your own risk. I do home on the probe once M561                            ...

We've found a Drawer_Gap of 1.0 (mm) to be sufficient, but results will vary for different 3D printers. If unsure, you can test the gap by printing a drawer of your chosen dimensions and a chest for a single drawer (Drawers_Across set to 1 and...

Here is a photo of an early attempt of me replacing the ceramic by a part from a piezo buzzer :Achim has written very detailed instructions for the restoration of Tefifons, including how to replace the cartridge by a cheep Chinese one that is readily...

Lots of lenses were made in these mounts, but their very short flange distance meant that they were orphaned when Canon switched to their current, incompatible, EF autofocus mount -- at least until mirrorless bodies with short flange distances came...

It's mag-fed and full-auto, with 95% drop-in 3D printed parts. Most of it can just be printed and dropped into the existing mounting points, but there are some (non nerf standard) screws, a pen spring, and Bondo. Had it out at a Nerf war recently,...

the design below will produce 12v AC. parts list: 2x bearings - 8x22x7mm: https://www.amazon.com/gp/product/B07V3NG2XR/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&amp;th=1 28 gauge enameled copper wire:...

Cure and dry your 3D resin prints in mere minutes. I used to have a setup with a UV led strip, but that turned out to take hours.</p> <p>This is a completely redesigned version of the UV resin curing that I currently use. The main idea was to make...

:P Time-lapse print video : https://youtu.be/BmbYEOAFL44 Subscribe to find out more support free 4K Time-lapse video: Subscribe Now!http://www.youtube.com/iczfirz Addiction to 3D Printing? Watch these time-lapse! ... https://youtu.be/-ZsXFX6hjXk <a...