pps43 receiver 3d models

GEPRC CineKing Receiver Antenna Mount. Since GEPRC does not release any STL files to print replacement parts I had to design my own. ...I designed this using TinkerCad easy and free.

This receiver holds high-definition media securely in place with a compact frame measuring 170x40mm and a sturdy mount that fits snugly on most standard-sized VESA brackets at 200x200mm.

Vises block .308 lower receivers based on DPMS LR308 standard from applied-kinetics.com. ... Directions: print vise carefully, be cautious of warping, since block can become warped and still function.

This is a simple holder for a FS-iA6B Radio Receiver. The holder is 49 mm wide, 12 mm in height and 10 mm deep. ...The mounting holes are 39 mm apart and uses M3 or #4 screws.

Built a mounting deck for a VTX and receiver that seamlessly integrates with Sergio's SMA mount. ...Developed two distinct versions: one tailored for hex standoffs, and another optimized for 5mm standoffs.

This is a renforced AR-10 Lower receiver. ...This 3d model is considered an art project, I could in any case and under no circumstances be related to any improper use of a third party or any person.

Black Mamba receiver for AAP-01.This is the project I did last year. It's done, but only part of the model can be made public for the time being. ...Other parts may be uploaded later.

Receiver mount for the FrSky V8R7-II receiver mounts to most models with double-sided tape, but I included clip tabs designed specifically for attachment to Eachine Racer 250 frames. After placing the mount in position, insert the clips and secure...

This vertical receiver boasts dimensions of 36 inches in width and 140 inches in length, offering ample space for various applications. ...Its upright design makes it a versatile choice for those seeking efficient storage or display options.

A user opted for a versatile receiver, which comes in a compact design that requires an external power source of 5 volts. ...A lithium polymer 2-cell pack paired with a step-down converter is found to be highly effective.

A friend of mine had lost a knob for their speaker receiver and I modeled up one based off of another from the same unit. Printed in Hatchbox black pla

The Graupner GR-16 receiver features a mount with pre-drilled holes for attaching antenna tubes, and in its updated version 2, it additionally allows for easy sensor plug attachment.

This is a clip-on holder for a Spektrum AR10100T 10-channel telemetry receiver. ...It can be mounted on a support in your airplane either by using sticky tape or 2 M3 screws.

This is the new Vertical Slider for the Optical receiver 3-axis mount, designed specifically for use with the Optical Rail System in order to securely mount the receiver. To complete the 3-axis mount, you will also need a Horizontal Slider and a...

This issue becomes even more crucial when combined with my modification, a removable wing design, which requires fast access to the receiver for easy servo connection to the ailerons. ... To ensure both parts stay together securely, you will need a...

FrSky X8R Receiver & Antenna Mount - I made this originally to be used with the FireFly http://www.thingiverse.com/make:235170 printable drone. I couldn't find anything that suited my needs in mounting and protecting my receiver. ...Just print the parts...

This print is specifically designed for receivers with the servo pins and bind button on the same side of the main board, as some receivers have their servo pins soldered on the reverse side. Please see photos, and check your receiver before...

Key Features: - Compatible with the Futaba R617FS receiver - Sturdy construction for reliable performance - Easy installation and minimal setup time - Suitable for a wide range of applications By investing in our mount bracket, you can trust that...

This is a collection of antenna mounts for the ExpressLRS 2.4 EP1 receiver from Happymodel that I designed to use in my TBS Source One frame, but I guess they work in any frame with 5mm diameter spacers.There are three options:Rear Vert Short. For...

This is a collection of antenna mounts for the ExpressLRS 2.4 EP1 receiver from Happymodel that I designed to use in my TBS Source One frame, but I guess they work in any frame with 5mm diameter spacers. There are three options: 1. Rear Vert...

For optimal performance, we recommend using our Marine GPS Antenna / Receiver Holder indoors, where it will be protected from the harsh elements. The low thickness and lack of UV resistance in most PET filaments make it an ideal choice for indoor...

To complete you'll need: 2 x M3x10mm (12mm is ok too) for the cap retainer 2 x M3 nuts (locknut optional) for the cap retainer 1 x M3x20mm (or so) to allow the cap to screw into the stock location The stock gasket is required and you'll need to take...

The goggles come with covers over the receivers, but they have holes in them which isn't a big deal if you use the cover for the front of the goggles, but I'm not into bling so I made a blank cover without holes to pop into the empty bay. I used it...

The standard configuration allows a small foam pad to be attached, minimizing vibrations that reach the receiver, while the low-profile option is perfect for electric applications. This versatile plate features four screw mounting points or can be...

With this initial release the stock ESC is still needed though a clip for no ESC (in the stock location) is on the way. This fits both the stock receiver box and the Vitavon aluminum mount (as pictured). To complete you'll need: 2 x...

The initial mount design has built-in clips that lock the receiver in place and ensure the circuitry/wiring doesn't get trapped. Mine weighed 0.78g. The second one has a narrower inside frame but is identical to the first apart from that. This one...

Models of Traxxas TRX4 box cover: 1) with window 2) without window window enables You to look inside the box and check wether receiver light is blinking and receiver is working. This window lets You check presence of water in case Your TRX4 is...

A Case for Protecting the FlySky/Turnigy X6B RC Receiver.\r\n\r\nOne of this receiver's features is its compact and "naked" design, but it leaves it vulnerable to damage in the harsh world of RC systems if not properly protected. ...Perhaps someone will...

Ultimately, I purchased a zipper case for the mouse and decided to make a holder for the receiver. This should be printed in TPU (or some other flexible filament). ...It grips fairly tightly and should not let the adapter fall out unintentionally.</p>...

I purchased a Logitech MX Master and was shocked to discover that the Unifying Receiver lacked on-device storage. Frustrated with this limitation, I opted to buy a zipper case for the mouse and designed a holder specifically for the receiver. This...