power of the primes volcanicus 3d models

... well it fits and holds Swoop once printed, as this will help refine the design. To assemble it, you'll need to print one of each file and then glue them together before inserting the combiner peg into the holes on V's back just like my Slash Pack.

This design will enable her to attach to Volcanicus as a powerful energy source, acting as a sort of power pack. The final version includes multiple 5mm ports to hold each individual Dinobot's weapon when in combined mode. This attachment consists of...

... Since I'm unsure how well it will function, I've avoided adding any details to the design for now. Version 2 of the pack features a slightly larger box opening compared to Version 1. ...While Version 1 should work, it was very tight in fit.

Here's a sword for Power Of the Prime Volcanicus that I made as a commission. Blade is about 15cm long with a 2cm handle. Added a photos of both Volcanicus and PotP Grimlock holding the sword. These 2 photos are not taken by me, because I don't...

G1 based Sword for Transformers Power of the Primes Deluxe Class Sludge. Can be used on any 5mm hole, has side mounting 5mm peg. Print out on .2mm Layer Height, use supports and a Raft. ... For personal use only, not for use in reselling, casting or...

G1 Based Sword for Transformers Power of the Primes Deluxe Class Sludge. Can be used on any 5mm hole with side mounting peg included. Print at a .2mm Layer Height using supports and a Raft. ... For personal use only, not for resale or use in casting...

Scanned and modeled Power of the Primes Grimlock arm. ...You'll have to mirror it in your slicer software or where ever you want.

A Pair of Weapons for Power of the Primes Battletrap. Can be used by the individuall robots in both modes, as well as the combined form. ...They're also both blast effect compatible.

This model showcases a high-end blaster designed by the Transformers Power of the Primes franchise. ... Optimal results achieved when printed via SLA/DLP technology for razor-sharp details and crystal-clear precision.

Transformers Power of the Primes assault rifle is available at this link - https://www.thingiverse.com/thing:3691512. To get your hands on Transformers Optimus Prime's blaster cannon, click on this - https://www.thingiverse.com/thing:3689670. ...For the...

This is one of the blasters from the Transformers Power of the Primes series. Best printed on an SLA/DLP printer for highest resolution. Check out all of my transformers guns! Transformers CW sunstreaker gunsword -...

G1 based Sword for Transformers Power of the Primes Deluxe Class Sludge. Can be used on any 5mm hole, has side mounting 5mm peg. Print out on .2mm Layer Height, use supports and a Raft. ...For personal use only, not for use in reselling, casting or...

You're free to print a custom-fitted ball cap and a versatile bat for your Power of the Primes Jazz figure! The cap is specifically designed to fit Jazz's head perfectly, while the bat features a 5mm handle that fits most recent Transformers figures...

A set of accessories for the Transformers Generations Power of the Primes Legends Class Windcharger mold based on the set I original made for the old Combiner Wars Windcharger figure, which were based on the original Magnets featured on the RTS Scout...

... to match a specific style, inspired by the G1 toy sword, ensuring uniformity throughout the collection. ...To achieve this cohesion, they were created with the intention of being printed using translucent materials, allowing for a consistent aesthetic.

... In the final image, Abominus can be seen with all current upgrades. The new knee covers are part of this collection, found here: https://www.thingiverse.com/thing:3106553 and https://www.thingiverse.com/thing:2825567

The absent sword in the Predaking release needed to be printed twice and carefully assembled into a single piece.

Here's an alternate chest upgrade for your Power of the Primes Volcanicus! This upgrade accomplishes three things. 1) It fills in the front of Volcanicus's chest, 2) It stabilizes Volcanicus's arms, and 3) It features two doors behind which you can...

Shoulder upgrade parts for Power of the Primes Leader Rodimus Prime.Joint design is inspired by method used by Ultraman Zoffy in 2018.Joint parts replace the back of the small Rodimus's thighs. ...Should be able to reuse the same screws, just swap the 1...

This is a sturdy base unit designed specifically to integrate the Prime Master emblem. ...Fingers crossed, it will be instrumental in mass-producing bulk prime cores.

This is a cap for Transformers Power Of the Primes RODIMUS UNICRONUS shoulders. I think it's work with Rodimus Prime too. Just clip on the back then in the front. ... Do not rotate the part for printing or you may get errors.

The Requiem Blaster, as seen in Power of the Primes. This can fit for any figure with 5mm hands. ...Only two colors need to be used for screen accuracy, black for the whole body and purple for the sides (see pic for reference).

Some upgrades for Optimal Optimus Power of the Primes figure let it transform into tank mode and more. The archives are for: a) Poseable hands with articulated fingers and phalanges. Each finger base attaches to the hand with wire, allowing one...

Some upgrades for Optimal Optimus Power of the Primes figures allow them to transform into tank mode and more. Archives include: a) Poseable hands where each finger (and phalanx) is articulated. The wrist and each finger base attaches to the hand...

Made to fit onto a chop-jobbed Power of the Primes "Slug". You'll need to remove the pin that connects the back of the head/jaw to the figure, save this pin because you'll need it later. Remove the pin by putting a brad nail against it and tapping...

... limbs to one torso port. ...I haven't printed it yet, so let me know what adjustments need to be made. V1 of the splitter performed well, but the test print was very tight. ...I've uploaded a second version of the file with a larger box opening.

So if any of you recall, Jazz at one point in the G1 cartoon sported speakers on the sides of his hips, prompting me to recreate that feature with a modern spin to match POTP Jazz's sleek design. This innovative 2-piece print boasts an effortless...

This being my first ever print, the level of detail is intentionally minimal. As it stands, there isn't an established method for storing this sword, but I'm actively working on finding a solution to address this issue. ...Nevertheless, I'm pleased to...

Had this guy and wished he had a shoulder mount like the G1 toy. ...Took some dimensions and an hour later boom here we are. This is a simple Bracket With a 5mm peg and 5mm port for any sort of weapon you want to mount on his shoulder.

Replacement for Swoop's thigh piece which snapped upon opening the box! ...