power and control lightsaber 3d models

... Order. ...If you enjoy what I create, consider adding a like or following the model - both are greatly appreciated! If you decide to print one of my designs, please share its make, as it's wonderful to see my creations being used and enjoyed by others.

... me to devise an improvement. By studying the original design, courtesy of MrBlizzard's creative vision, I successfully integrated it into my own unique concept. The result is a sleek and functional upgrade that showcases my problem-solving prowess.

This is my custom lightsaber design, a direct homage to Anakin's iconic blade. ...As soon as I've completed the build and added the finishing touches, including a fresh coat of paint, I'll be sharing photos of the final result.

I built a straightforward stand to showcase my impressive lightsaber collection, and you'll want to scale it up significantly. ...I determined that scaling it up to 275 is an excellent choice for virtually any saber hilt - note that it doesn't...

I drew inspiration directly from the grip of Anakin's iconic lightsaber, combined with the radiant emitter of Luke/Obi-Wan's signature blades, and integrated a sturdy hilt reminiscent of Cal's impressive design. ...The end result is a masterpiece that...

Inspiration taken from https://www.myminifactory.com/object/3d-print-vertical-lightsaber-display-stand-87988 I wanted a vertical saber mount for my desk so it would take up less space. ... This stand is made for my RPF sourced Luke stunt saber and Obi...

The other change I made to it was I made a gap below the clamp area, as there is an ic at that spot that I didn't want to be clamping.You will need 2x M3 x 10 mm screw (or 15mm with nuts) (for SCART connector)2x M3 x 10 mm screw (for HDMI output...

Hello, because xpt2046 is now supported in EspHome for HomeAssistant, i make a simple remote control to put on the living room table to control most of my light in the house. needed: - 2 x Esp32-Wroom-32 - 1 TP4056 charge module - 2 TFT ILI9341 with...

However, this setup helps keep the remote control in its designated spot and the headphones docked at all times. The fan stand it mounts to is 1 inch thick. The ingenious mount design by @Kawobei ensures a snug fit, being only a fraction under 1...

I developed this sketchy physics landing craft, which requires Sketchy Physics, as an experimental model for demonstrating stability control device functionality derived from helicopter thrust mechanics. Typically, if left unchecked, an unstable...

A bracket-style enclosure designed to house and stabilize the control board of 3D printers, primarily intended for the Tevo Tarantula but potentially suitable for other models as well. Created specifically to accommodate the MKS Gen 1.4 board with...

I found the the thing this is based on and adapted it to create a flange to hold the PTFE fitting (same as the original http://a.co/d/bXJCLVm) I bought some more PTFE Teflon Bowden Tube http://a.co/d/efHZAR9 and set it up with break in the tube to...

Some additional wall control brackets to go with the amazing DDD Printable Wall Control project. The hex bit holder is a remix of https://www.thingiverse.com/thing:1692958 however, thingiverse wont let me add an additional source I like to print the...

Both are designed to work with Geeetech GT2560 Rev A+ (and may fit other models as well). Version 2 is created for Raspberry Pi Zero, also featuring space for a DC-DC converter. Attached is a cover with cutouts for two 40mm fans. Version 3 is made...

**Check the original model for all required parts and mounting hardware:** https://www.thingiverse.com/thing:1767285 **Useful links:** * MOSFET: https://www.amazon.com/initeq-MOSFET-Printer-Controller-Current/dp/B073QGHTZL * Original model by...

A brilliant engineer constructs a razor-sharp lightsaber within the iconic Star Wars universe of 2014.

This Lightsaber is not from a film its by me, enjoy it :)

Lightsaber parts meant to go over a 1.25 OD aluminum tube. ...

Star Waras jedi lightsaber model. ... renders with green "blade" are done in NX

The compact lightsaber measures approximately 200 millimeters in length as it stands.

These are 3d models of 6 cool lightsabers made on Fusion 360

My first creation, please dont be too harsh. ... Custom lightsaber claymore Modeled in Tikercad

Luke Skywalker's ROTJ lightsaber from the kenner line (1977-1983)

This basic lightsaber model is relatively unremarkable compared to others in its category.

This is a small-scale lightsaber hilt that was used to make a file handle.

Lightsaber wallmount, can use command strips or screws to hold on wall

This is a straightforward lightsaber model created using Solidworks 2013, not inspired by any specific design.

The custom-made lightsaber handle produced an impressive outcome as it emerged from the printer.

Two sleek lightsabers rest side by side, their slender hilts gleaming in unison.

this is the lightsaber that the inquisitors in rebels used it does spin