posca holder 3d models
372002 3d models found related to posca holder.
cults3d
Support for 8 POSCA 0.7mm tip (ref PC-1M). ... Allows to keep them upside down to avoid that the points dry.
thingiverse
4 by 4 inches wide and about 6 inches tall posca marker container. Not my idea. I didn't find a design like this on Thingiverse but I was inspired by a TikTok I saw. ...Also, this is my first design so if it doesn't turn out the best I am open to...
thingiverse
The organiser is specifically designed for Posca PC-1MR 0.7 mm markers, so the hole diameter is 14 mm. I've printed this organiser on a Creality Ender 3 v2, 0.2 mm layer height, 15% infill, with orange PLA. The grid has 4x4 holes, which can be...
thingiverse
A compact pen holder to securely hold and maintain a fine Posca marker.
thingiverse
I made a remix of the container https://www.thingiverse.com/thing:4786193 It's only for Posca PC-3M. ...It can hold till 45 markers
prusaprinters
... in Tinkercad, but I will make a better one also for the other sizes I use. (also fits the PC-3m and thinner Posca Markers)Play with the infill and all that, but for me I wanted some heft to it, so it wont tip over. Open for feedback obviously.
thingiverse
It has room for 15 PC-5M, 18 PC-3M, and 12 PC-1M (medium, fine and extra-fine.) Features the POSCA™ logo and a snazzy retro pattern seamlessly wrapped around the outside. ... I guess you could use it to store other things, but then the logo will look...
prusaprinters
Support 8 feutres POSCA PC8K pour pegboard SKADIS IKEALongueur : 215 mmLargeur : 30 mmHauteur : 42 mmPLA/PETGInfil: 15%Support pour les crochetsN'hésitez pas à me laisser un commentaire, ou poser une question.
prusaprinters
This stand holds 30 16.5mm diameter POSCA markers.No supports required as long as you have good adhesion. Brim is recommended. Minimal manual support in the middle of the slope could also be used. Max overhang is 30°. </p><p>I'd love to see your...
prusaprinters
Everybody seems nuts for POSCA™ paint markers/pens, so I got myself a set. I liked them so much that I bought two more sets so I had more sizes. But then I wanted a nice box to store and organize them in. It has room for 15 PC-5M, 18 PC-3M, and 12...
thingiverse
https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...
cults3d
Support 8 feutres POSCA PC8K pour pegboard SKADIS IKEA Longueur: 215 mm Largeur: 30 mm Hauteur: 42 mm
thingiverse
I wanted a nice box to store and organize the Posca Pens in and found one on Thinkiverse, thanks to CaptainFwiffo.It has room for 15 PC-5M, 18 PC-3M, and 12 PC-1M (medium, fine and extra-fine.) Features the POSCA™ logo and a snazzy retro pattern...
thingiverse
This is an adapter for the Silhouette Cameo plotter to use the Uni Posca PC-1MR like this: https://amzn.to/31SHVbI I felt extremely limited using the Silhouette SketchPen, so I designed this adapter to gain much more freedom and a wider variety of...
thingiverse
MarkerStand 13mm - holds up to 44 markers (Fits Posca (PC1M, PC1MR), Molotow (One4All Twin, 127HS)...) MarkerStand 17mm - also holds up to 44 markers (Fits Posca (PC1M), Copic Markers, ProMarkers) MarkerStand 19mm - designed for 27 markers (Fits...