porter cable pcb270ts 3d models

The original Porter-Cable 3.2-Amp 5-Speed Bench Drill Press Start Capacitor Cover came with a fragile outer casing that cracked upon opening the box. ...A precise replica was designed and 3D printed to replace it, yielding impressive results - the new...

This one for PORTER CABLE 20 volts lithium batteries.  The holder should be printed in the upright position and should require little to no support if your printer bridges well enough. I included two versions: one locking and one non locking. The...

The Leigh dovetail jig required Porter Cable style guide bushings, which were costly, but I soon found out that Harbor Freight sells an inexpensive set (https://www.harborfreight.com/9-piece-router-template-guide-set-98361.html). Then I needed to...

This is to repair the handle that broken handle for Porta Cable wet dry vacuum. From looking online I was not the only one whose handle broke off. It appears the part must be replaced by purchasing an entire new top which is now obsolete. This fit...

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/1VDf9WF7lf5

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/1VDf9WF7lf5

This creation is brought to life through Tinkercad's innovative platform. ...Modify it instantly online at https://www.tinkercad.com/things/4YRwMgPZb6C

Printable Template for Dovetail Jig Installation: Drill Holes According to Your Specific Setup Requirements.

I've been successfully utilizing these adapters for an extended period without any hitches. Nevertheless, my printing capabilities are limited to PLA, and whenever I accidentally drop the tool in use, the adapter's tool side often suffers damage. ...To...

Edited the original in Tinkercad so you can print it tip down with no supports. ...The model is a little rough but prints clean on a .04 nozzle and imperfections in model can't be seen.

Don't have a 3d printer, but will update as I am able to use it and have friends print for me. ...350mm x 150mm x 8mm

This creation is powered by Tinkercad. ...Make changes instantly at https://www.tinkercad.com/things/7Cv3c7GgWGm.

This prototype remains unfinished, pending thorough testing to ensure the mechanical component aligns properly with its intended counterpart.

I've beaten this poor impact driver for years and it keeps on taking it! See my other post for the Bosch battery adapter to use with this tool. I finally got tired of always having to stop what I'm doing and look for the driver I need. I designed...

After dropping one of my 20V lithium batteries and busting the button i created a replacement. This is printed using supports and I used PLA + but I am sure PLA would work as well. ...Happy printing!!

This is a remix of JESTERxHEAD's design, I modified it so it could be printed vertically, and therefore without need of any supports.

You can customize this band saw using the customizer tool to suit your needs. ...Click here to open it in a new tab.

I swapped out the old plate for one that was slightly thinner to compensate for its slight elevation on my machine.

This is a work in progress. ... Have not tested fit of printed part yet.

I was looking for a away to store my batteries on the wall and found this source. It was a very good model just a bit more than what I needed. I deleted a few of the features and shrank the outer rails a bit to make insertion and removal a bit...

<p>Polisher comes with a side handle, I wanted something in the center.</p> <h3>Print Settings</h3> <p><strong>Printer Brand:</strong></p> <p>Prusa</p> <p class="detail-setting printer"><strong>Printer: </strong> <div><p>i3 MK3</p></div>...

I was looking for a polisher that included a central handle, not just a side one.

Customized version of https://www.thingiverse.com/thing:1246651 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1246651

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/1VDf9WF7lf5

Both versions print upright with no supports.Be sure to set bridging settings.Adding wires and connectors is on you.

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/1VDf9WF7lf5

<p>Both versions print upright with no supports.<br>Be sure to set bridging settings.</p><p>Adding wires and connectors is on you.&nbsp;</p>