portable cubicle 3d models

Put this shower cubicle hook over the glass screen. It fits on 6.5mm glass shower cubicles. I use ANYCUBIC ECO resin because it stays white after curing. ... Happy printing :-)

Toilet cubicle found in offices, schools, entertainment venues etc. ...This asset is game ready, uses as few polygons and vertices where possible, omitting polygons when not seen e.g back of cubicle and toilet

Jabra speaker holder for Marnela cubicle wall. ... Created in Tinkercad https://www.tinkercad.com/things/eLgmH8PvFgp-jabra-marnela-stand

Remix expanding the depth of the hook for a 4cm cubicle wall. ...Everything else is the same as the original.

Remix expanding the depth of the hook for a 4cm cubicle wall. ...Everything else is the same as the original.

Now you can add a touch of darkness to your office cubicle by decorating it with bats!

xbox controller hanger for cubicle and spare AA battery slots. ... I did not need supports, your milage may vary.

Remix of Heavy Duty 3" Cubicle Coat/Backpack HookExpanded to 3.5" gapMade it double sided to provide hooks for both sides of cubicle wallRemoved bumps as my cubicle tops were flat glass. Squared inside corners for snugger fitPrinted with brim...

Too bad.) Extend your cubicles with cheap pieces of 3/32" foamboard, clipped onto the edges of the existing Steelcase partitions. The top clip will clip onto a cubicle edge 2-1/16 inches wide by 5/16 inches deep. It's slightly bigger than that. The...

This is a custom Coat Hook designed specifically for 3-inch Steelcase cubicle walls, marking its debut as my very first published project.

This bracket allows you to hang a whiteboard from the cubicle partition of your Steelcase or other 80mm wide panel system.

Standard consulting cubicle with two attendance seaters and one office seat. ...Its a 3d model with sectional details well drafted excluding labelling texts.

This is a HUGE collection of various props used to make office cubicles. ...The quality of the mesh and PBR textures is suitable for 1st person PC games.

This is a cubicle hook I designed to hang a whiteboard or corkboard on a 2" cubicle wall. Versions for a #6 or #8 machine nut & screw. ...Found here: https://amzn.to/3Uch8oNPrinted on side so layer lines are vertical when installed.

I love the design of the Cubicle Coat Catch by @SFYoung but it was just a little too short to actually catch in the older cubicle in my office. Its not perfect but I lengthened the catch hooks just a bit to make it fit. ...

The remixes are modified to hang from a glass cubicle wall or any thin cubicle wall of width about 12mm. 2 versions included: Version A holds a section 150mm X 65mm X 10mm; and, Version B holds a section 200mm X 100mm X 4mm. ... Designed with Fusion...

... this lovely coat hanger design by "honeydeltawings". ...Really loved the look, but the cubicle wall I had intended to use it on, was much thinner. Simply cut out a section of the "throat" of the hanger that spans the thickness of the cubicle wall.

It uses OfficeMax OIC Cubicle Hooks Item # 719164, also known as OfficeMax # 24159642...

I created a unique phone holder that attaches directly to my office cubicle's wall, allowing me to secure my phone and improve cellular reception - a simple yet effective solution for staying connected at work.

I loved the source model so I cut the head off and modeled the hanger based off the cubicle dimensions. I then made connector pegs to ensure a good connection. ...I'm very pleased with the results and I hope others will be able to enjoy this model as...

Type 1357 1.26 largo Ancho 850.0 850.0 Ancho puerta 600.0 600.0 Ancho tabique 10.0 20.0 Angulo apertura puerta 40.000° 40.000° Assembly Code Cost Description WC cubicle, side entrance WC cubicle, side entrance h comienzo tabique 250.0 250.0 h...

The panels around my cubicle are narrower than the original design & have padding on each side, so I added "spikes" that slip behind the padding & hold the pumpkin upright.Here's the bat that goes with itUse a brim if you have problems with...

Type Caseta Ducha 1.0 Altura base vestidor 80.0 Ancho 900.0 Ancho 2 900.0 Ancho panel frontal 350.0 Ancho puerta 550.0 Ancho tabique 10.0 Ancho vestidor 550.0 Apertura puerta 20.000° Assembly Code Base cambiador Base cambiador Base ducha 80 x 80...

I opted for a neater approach than the elaborate top-of-the-cubicle-wall designs I initially considered, which would have consumed an excessive amount of time. To keep my whiteboard eraser, cleaning fluid, and markers neatly organized in a more...

The panels around my cubicle are narrower than the original design & have padding on each side, so I added "spikes" that slip behind the padding & hold the bat upright.Here's the pumpkin that goes with itUse a brim if you have problems with...

Get creative and transform your workspace into a spook-tacular haven by adorning your office cubicle with vibrant jack-o'-lanterns! ...Take inspiration from the intricately designed Jack-o'-lantern shape found on Thingiverse, specifically in the design...

... of https://www.thingiverse.com/thing:3998792. ... I needed a cubicle hook that would work with a 3 inch partition, so I remixed the above in TinkerCad. ... There are 2 versions, one with grips on one side as the original and V2 has grips on both sides.

A flat shelf, supported at the corners, that overhangs both sides of my cubicle walls. I printed it upside down so that no supports are necessary. PLA works fine, and infill can be light. ...I've had this holding a heavy potted peace lily for months...

I added "spikes" to hold the bat upright by slipping them behind the padding on each side of the panels around my cubicle, which are narrower than the original design. ... The pumpkin that matches it is available here:...

The panels around my cubicle are narrower than the original design and have padding on each side, so I added "spikes" that slip behind the padding to hold the pumpkin upright. ... Here's the bat that goes with it:...