portable ac hose adapter 3d models

This is made to fit the hose of my particular make and model, of the brand “Anslut”, but I suspect it's pretty standard.Print instructionsI printed in the orientation of the cover picture, with supports on the horizontal window frame bar and the...

Adapter to bridge a standard 5in counter-clockwise portable air conditioner hose to a Honeywell AC unit. Tested on model HF0CESVWK6 but may work for similar units.Note that this is specifically targeted to fit these Honeywell units that uses a...

A DIY upgrade for the GE APC09YZMW 5600 BTU/H portable air conditioner involves adding an external air intake system. ...Currently, no attachment method exists, so a temporary solution would be to secure it with adhesive tape until a more permanent...

Adapters for turning a portable AC equipment into a 2-hose solution, increasing effectivity. These adapters have been designed to suit a 150 mm exhaust hose, and a 160 mm inlet hose. The unit I used were a Deltaco Smart AC 9000 (SH-AC01), but other...

to adapt 5" - 5.1" hose to the male receiver found in many portable air condition systems, including Haier brand. these portable air conditioners can be found on the second hand market for cheap, but often are missing this critical part to properly...

Universal exhaust adapter for portable air conditioners, compatible with diameters ranging from 125mm to 100mm.

I successfully created a custom window adapter for my portable AC (Black & Decker BPACT12HWT) using OpenSCAD and printed it out. My DIY version is almost as fragile as the original, but it has fewer leaks and fits more snugly than the real one. To...

This is a set of portable air conditioner adapters for the vent hose. I started with some timber of 140mm x 12mm cut to the length required to neatly fit into the window. Using the router template, I used a router bit with a bearing to route a...

The problem is that it takes in warm air at room temperature, blows out a portion of it back into the room, cooler, while sending the hotter part outside through a hose attached to a special panel in the window. However, this leaves you with negative...

Adapter for the exhaust spiral hose for a Sandstrøm/Sandstrom SAC12C13E portable air conditioning unit. It will probably fit other units too. The hose diameter is 150mm / 6 inches. The adapter has a reverse thread, so it should be possible to fix the...

I'm designing an adapter that fits snugly onto my portable AC unit, allowing the hose to be securely attached. This is version one of my prototype. To make it work, I drilled some fixing holes into place so they can attach to the corresponding holes...

I lost the adapter for my portable AC to a 5 inch flex duct. I remixed jollino's coupler (thanks) to make an adapter. It fits a Honeywell mn10cesbb and possibly other Honeywell mn models. It is a friction fit with the internal tabs on the ac unit and...

I designed an adapter to fit my portable AC unit's low-profile oval end after discovering that the window kit provided didn't work with my window style. This custom-made adapter fits snugly onto the 6-inch diameter exhaust tube, ensuring a secure...

Small plate to fill in the middle gap from using the extender on the LG portable AC window adapter. This is meant to go over the extender bracket and be screwed in. I used counter-sunk screws for mine in order for it to sit flush against the...

The included window adapter for the AC unit required minimum 20" but my window was only 14" so I made a custom adapter to fit 14" sliding windows. I included the f3d file for anyone that wants to modify the length/width for other size sliding...

Attachable Hose Fitting That Secures To A Window Sash And Accepts A Flexible Tube From A Portable Air Conditioning Unit.

130mm (inside) vent hose adapter to connect insulated hose ACHose is the adapter to connect the insulated hose, ACHoseTubeHole is the screw-on connector for the AC side. Print the former twice, the latter once, and connect one of each with M3 bolts.

... installed. ...To rectify this issue, I created a custom wooden bracket to secure the unit within the window opening. The hose provided serves a standard 5-inch diameter connection, commonly utilized by numerous portable AC units on the market today.

I have designed and printed it for my electrolux portable AC.

I have designed and printed it for my electrolux portable AC.

Hose adapter for 6" AC outlet

An adapter for portable AC unit CHiQ brand but may fit other For standard hose included in the kit

This is a dual hose adapter for the Tristar AC-5529 which drastically increases the efficiency of the portable AC. Fits a 152mm hose. ... Print parts 1->4 and glue together, depending on your print settings you may need the "supports" which basically...

Converts threaded female AC Vent Hose fitting (for portable air conditioners) to 3" hose barb for use with regular 3" duct and hose clamp.

This print is a cowling which fits over the air intake on the old version of the Rollibot Rollicool Portable AC and outputs to a 5" vent which you can then adapt to the existing window spacer that the existing exhaust hose vents through. Bill of...

Use this adapter to attach a 10mm internal diameter hose to a portable air conditioner's drainage outlet, designed specifically for the Mistral MA10KR/D model. This DIY solution was created by molding clay into the threads of the end cap that...

This is a part I designed to have a clean hole for my Delonghi Pinguino portable AC unit to expel the hot air without having to keep my window open Solidworks files are provided so you can mod this to fit the exact thickness of your window by...

Human: Had to extend my exhaust hose on my portable AC after following this Amazon review : https://www.amazon.com/gp/customer-reviews/RHTXOMLKK2RAC/ref=cm_cr_pr_rvw_ttl?ie=UTF8&ASIN=B0048ELABM Didn't want to cut the provided wall adapter, so I...

I got some proper isolated fan duct hose and wanted an adapter to be able to connect it to our AC unit. The outer dimensions on the thinner side is 120 mm, and on the larger side: 145mm.</p> <p>I printed it in PETG to be able to stand the higher...

The adapter is designed for use with my corrugated hose, which measures 14 cm in diameter and standard ventilation holes found in Sweden. The screw holes on the adapter are spaced 12.5 cm apart, providing a secure fit. ... Unfortunately, my print had...