portable ac drain hose 3d models

Use this adapter to attach a 10mm internal diameter hose to a portable air conditioner's drainage outlet, designed specifically for the Mistral MA10KR/D model. This DIY solution was created by molding clay into the threads of the end cap that...

AC drain hose connector that comes with most EU Air cons.

This is made to fit the hose of my particular make and model, of the brand “Anslut”, but I suspect it's pretty standard.Print instructionsI printed in the orientation of the cover picture, with supports on the horizontal window frame bar and the...

Made this for my floor drain specifically to accommodate a 7/8 AC drain tube, which I secured with super glue to a cap that fits perfectly. The adapter has a diameter of 4 1/4 inches and features a hole in its rear side where the hose can be...

... of the tapered screw. I have redesigned it summer 2019 and am offering it for sale here: https://smilingimpact.ecrater.com/p/33864416/air-conditioner-window-ac-drain https://www.ebay.com/itm/202702059487 https://www.ebluejay.com/ads/item/7335702

I have redesigned it summer 2019 and am offering it for sale here: https://smilingimpact.ecrater.com/p/33864416/air-conditioner-window-ac-drain https://www.ebay.com/itm/202702059487 https://www.ebluejay.com/ads/item/7335702 Custom Section Category:...

Adapter to bridge a standard 5in counter-clockwise portable air conditioner hose to a Honeywell AC unit. Tested on model HF0CESVWK6 but may work for similar units.Note that this is specifically targeted to fit these Honeywell units that uses a...

... ...So, I decided to reduce the top screw size slightly, which ended up positioning the four side holes roughly halfway down the drain. ...This creates enough space for condensate to flow into those side holes rather than getting stuck at the very top.

Attachable Hose Fitting That Secures To A Window Sash And Accepts A Flexible Tube From A Portable Air Conditioning Unit.

Adapters for turning a portable AC equipment into a 2-hose solution, increasing effectivity. These adapters have been designed to suit a 150 mm exhaust hose, and a 160 mm inlet hose. The unit I used were a Deltaco Smart AC 9000 (SH-AC01), but other...

This can accommodate a 30mm hose, so it's wide enough to fit a common US 1-inch hose. My drain hose is flexible, so I also added a retaining clip to slide into the grooves of the hose to keep it from sliding out. It's 1.5mm thick with a 19mm...

This can accommodate a 30mm hose, so it's wide enough to fit a common US 1-inch hose. My drain hose is flexible, so I also added a retaining clip to slide into the grooves of the hose to keep it from sliding out. It's 1.5mm thick with a 19mm opening...

A DIY upgrade for the GE APC09YZMW 5600 BTU/H portable air conditioner involves adding an external air intake system. ...Currently, no attachment method exists, so a temporary solution would be to secure it with adhesive tape until a more permanent...

This is meant to be an alternative to LG part number COV36133186 for the LP1021BHSM Portable AC/Heater (It may work with other units). ...This was designed to fit standard 3/8" ID clear tubing.This was my first attempt at making a 3D model, but I was...

to adapt 5" - 5.1" hose to the male receiver found in many portable air condition systems, including Haier brand. these portable air conditioners can be found on the second hand market for cheap, but often are missing this critical part to properly...

After watching the video below on youtube, I realized just how inefficient my single hose Rollicool Portable AC was so I set out to fix that. This print is a cowling which fits over the air intake on the old version of the Rollibot Rollicool Portable...

This is a remix of roosteralex82's drain hose holder for those of us who have to empty their portable washing machines into the tub (ask me about my Panda washer!). It juuuust fits a ~4" rim (~10.16cm) and, at 6.75in/171.4mm width, can be printed on...

This is a part I designed to have a clean hole for my Delonghi Pinguino portable AC unit to expel the hot air without having to keep my window open Solidworks files are provided so you can mod this to fit the exact thickness of your window by...

A thing for Portable AC

I just got a portable AC that didn't come with the ventilation hose, so I went to Home Depot to see if they had any. Unfortunately, they didn't have the right hoses or anything else that fit my budget of under $20. Instead, I picked up a dryer vent...

Drip catcher to hose barb. ...I attached it to the underside of the AC with hot glue

Install a portable AC unit by utilizing your existing dryer vent as a conduit. ...This involves attaching the AC's exhaust hose to the dryer vent, creating an efficient and convenient way to cool down any space, be it your home or office.

Replacement exhaust hose adapter for my portable ac machine. Tolerance is very, very tight. Because I used PLA, the "clips" ended up breaking due to PLA being very brittle. If I used a more flexible filament, they could probably have ended up...

AC elbow drain pipe connector that I made as a replacement for the original that broke.Printed with supports but only on the build plate. ...Layer height 0.2 mm with 100% infill.Recommend making it with PETG or ABS since it should be used outside.

This exhaust adapter is for an Arctic Cat Portable AC Unit. ...It slides in the back and has attachement for the 6" air duct.

This exhaust adapter is for an Arctic Cat Portable AC Unit. ...It slides in the back and has attachement for the 6" air duct.

To help our apartments not be like saunas, we have started to buy portable AC devices; only, sadly, that most of them come with window attachments totally unsuitable for common casement windows.With a 3D printer and some supplies, you can overcome...

I recently purchased a second LG portable AC unit that lacked essential accessories. To overcome this issue, I utilized the first unit's components as a template to create a digital model, which I then printed out. This custom solution will perfectly...

I successfully created a custom window adapter for my portable AC (Black & Decker BPACT12HWT) using OpenSCAD and printed it out. My DIY version is almost as fragile as the original, but it has fewer leaks and fits more snugly than the real one. To...