porsche 986 cup holder 3d models

Remix of trevorbattle's Cup Holder design. This base lets you place items inside (other than drinks) without removing it to grab something. It fits neatly into my car. Despite being PLA (in this case), it has withstood the Florida heat for a month...

Remixed to fit American size drinks. ...Can fit a small camelbak water bottle or 32oz soda cup. ... Print upside down with supports.

In my situation, I'm using this to replace the malfunctioning in-dash cup holders so I can utilize that space for a double-din stereo upgrade. The lid still closes and locks securely with the cup holder installed. With the Boxster, the lid opens...

Add a cup holder to your Porsche 996 or 986 after deleting the ashtray part. First, pull up the rubber lining and remove the two screws holding it in place. Place the bottom piece of the cup holder in its designated spot - it only fits one way. Put...

This phone holder was designed to fit the phone holder below, which can be purchased from Amazon. ... Link: https://www.amazon.com/dp/B07KF7R8L2?psc=1&ref=ppx_yo2ov_dt_b_product_details General Print Settings Material: PETG-CF Layer Height: 0.2...

Holder for bigger speakers for Porsche Boxster 986. ...Print with PET and 50% infill.

I own a holder that fits perfectly inside my Porsche Boxster S 986.\r\nTested it on my 2001 model, so it should fit all cars within the same range.\r\n\r\nYou could lower the bars holding the can in place, but I prefer to keep them higher to minimize...

Manufactured from ABS, this product necessitates a phone holder equipped with a magnet on the device and a sphere bonded to the holder. ...The printed holder must be fastened securely with screws or tape, ensuring that when removing the phone, the...

https://www.thingiverse.com/thing:3268454 If you prefer another Phone holder in It's place, message me and I will make a custom mount for it for the Porsche. I just liked this guy's. If the Car mounting parts are confusing to put together just...

Push Connecter into iPad holder with connecter arm facing the shorter half of the iPad holder 4. line up holes on the Car Mount to connecter piece with the arm looking like \\ 5. Push connecter tube into Car mount 6. ...Turn clockwise until...

porsche 986 first generation boxster.

porsche 986 first generation boxster.

AC Bracket for Porsche 986 V1

Designed to fit the Tamiya 1/24 Porsche 986 Boxster. ... The insert resembles the trunk reinforcement of the real car.

Replacement cup holder for the ash tray in a Porsche 944 S / S2 or other later Models. Designed to mimic the ash tray styling. Size perfect for Energy drink sized beverages or coffe cups. Adapters inculded for Fast food cups and bigger cans. ...

Designed to fit the Tamiya Porsche 986 Boxster. Theoretically, it should fit the Porsche 996 from Tamiya too, but this is still untested. The insert resembles the hood reinforcement of the real car. 2022-06-08: Altered the design to aprox 30%...

This is a straightforward tool for installing RMS (Rear main seal) on Porsche 996 and 986 engines. When the tool is fully seated against the flywheel flange, the seal will be positioned precisely 13mm below the crankshaft flange. Use the flywheel...

I went ahead and created new fonts and numbers for our Porsche 986 as the old one were long gone. This has been our fixer upper car and it was great to print a part that are as expensive as 80 euros.&nbsp;</p><p>The print is pretty simple and is as...

Removable cupholders for Porsche 986 Boxster. Bracket wedges in between Center dash and Upper Center Console as shown. Cupholders can be stored in armrest when not in use. Assembly Instructions: 1. Insert the shorter side of bottom supports...

The cup holder can be easily removed (so you can slide the seat forward all the way) by pulling the cup holder upwards from the bracket. I don't know if the mk2 996 floor/center console is 100% identical, I made this for my 996 2000 mk1. The...

Note that there are two holes on the stand where you can screw in the cup holder - just choose the one that fits best with your particular setup. Printing without supports should be a cinch. ...When printing this design, we recommend using ABS or Nylon...

This is a clutch alignment tool for a Porsche 986 S

This is a cam holding tool for the Porsche 986/996 Boxster or 911 early 5-chain engines.

The original cup holder insert was a bit narrow to fit my cup :-) Made one that was slightly larger.

The original cup holder insert was a bit narrow to fit my cup :-) Made one that was slightly larger.

This cup holder fits the spare change cup on the center console where the ashtray used to go in my 2000 Boxster S. ... I have also included the fusion 360 (,f3d) file so you can modify it.

This modification works seamlessly with a 1999 Porsche 996, although it's uncertain if it will be compatible with other model years. The design was created using Tinker Cad software. A standard can diameter container fits perfectly into the space...

A 986 has over a dozen of these nuts, they're also used to secure the carpet on the engine cover behind the seats. The original ones tend to get loose or break over the years, so I needed a few new ones. I designed these using a 10mm nut and...

These brake disks resemble the Brembo brake disks as used on Porsche 996 and 986 models. A small disk (13.4mm) for the rear and a slightly larger (14.5mm) one for the fronts. Designed to fit Tamiya 1/24 kits. The design is unsupported and might...

This part is used on (at least) the 996 (911) and 986 (Boxster) to secure a plastic cover between the headlights in the front trunk (frunk). You'll need 4 of these to secure the plate. The original ones had broken "legs" or humps at the bottom, so...