porsche 986 calipers 3d models

... dimensions tolerance is +/- 0.25mm, while the external dimension allows for a variance of +/- 1.25mm. ...This applies to Porsche Boxster S 986 L R rear red brake calipers with part numbers 996352421 and 996352422, having a total cost of $86,562.

porsche 986 first generation boxster.

AC Bracket for Porsche 986 V1

Holder for bigger speakers for Porsche Boxster 986. ...Print with PET and 50% infill.

Designed to fit the Tamiya 1/24 Porsche 986 Boxster. ... The insert resembles the trunk reinforcement of the real car.

Designed to fit the Tamiya Porsche 986 Boxster. Theoretically, it should fit the Porsche 996 from Tamiya too, but this is still untested. The insert resembles the hood reinforcement of the real car. 2022-06-08: Altered the design to aprox 30%...

This is a straightforward tool for installing RMS (Rear main seal) on Porsche 996 and 986 engines. When the tool is fully seated against the flywheel flange, the seal will be positioned precisely 13mm below the crankshaft flange. Use the flywheel...

I own a holder that fits perfectly inside my Porsche Boxster S 986.\r\nTested it on my 2001 model, so it should fit all cars within the same range.\r\n\r\nYou could lower the bars holding the can in place, but I prefer to keep them higher to minimize...

I went ahead and created new fonts and numbers for our Porsche 986 as the old one were long gone. This has been our fixer upper car and it was great to print a part that are as expensive as 80 euros.&nbsp;</p><p>The print is pretty simple and is as...

Removable cupholders for Porsche 986 Boxster. Bracket wedges in between Center dash and Upper Center Console as shown. Cupholders can be stored in armrest when not in use. Assembly Instructions: 1. Insert the shorter side of bottom supports...

This is a clutch alignment tool for a Porsche 986 S

This is a cam holding tool for the Porsche 986/996 Boxster or 911 early 5-chain engines.

These brake disks resemble the Brembo brake disks as used on Porsche 996 and 986 models. A small disk (13.4mm) for the rear and a slightly larger (14.5mm) one for the fronts. Designed to fit Tamiya 1/24 kits. The design is unsupported and might...

A 986 has over a dozen of these nuts, they're also used to secure the carpet on the engine cover behind the seats. The original ones tend to get loose or break over the years, so I needed a few new ones. I designed these using a 10mm nut and...

This part is used on (at least) the 996 (911) and 986 (Boxster) to secure a plastic cover between the headlights in the front trunk (frunk). You'll need 4 of these to secure the plate. The original ones had broken "legs" or humps at the bottom, so...

This attaches to the clutch master shaft to reduce clutch pedal travel for use with clutch disks which need over-travel protection (e.g. ...a Tilton OT-2 7.25" twin disk)

This phone holder is meant to fit inside the empty storage slot underneath the radio. This phone holder was designed to fit the phone holder below, which can be purchased from Amazon. ... Link:...

The 3D model was built on a genuine car base. It's constructed precisely, in actual units of measurement, with high quality and maximum similarity to the original. Model formats: - *.max (3ds Max 2008 scanline) - *.max (3ds Max 2008 vray) - *.fbx...

Ball mount for phone holder for Porsche 986 stock stereo. I modified it from: https://www.thingiverse.com/thing:4706682 in TinkerCAD the ball appears to be about 17MM. Worked perfect with a phone holder I already had. ... I printed it and put...

Add a cup holder to your Porsche 996 or 986 after deleting the ashtray part. First, pull up the rubber lining and remove the two screws holding it in place. Place the bottom piece of the cup holder in its designated spot - it only fits one way. Put...

This is a Phone Mount for my Porsche Boxster 986 S Spyder from 2004. The ball joint allows you to change the viewing angle of the Tablet/Phone you want to use. I Custom made the mount to perfectly fit on the upper right part of the storage...

modification du CDTRay de la Boxster 986 2002. démontage avec précaution du CDTRAY pour conserver le cadre. Impression des 2 modules Pour le Module de support il faut enlever les support pour dégager la gorge ou les clips se positionneront Vis M3...

Remix of trevorbattle's Cup Holder design. This base lets you place items inside (other than drinks) without removing it to grab something. It fits neatly into my car. Despite being PLA (in this case), it has withstood the Florida heat for a month...

PORSCHE 987 / 986 REAR UPRIGHTS DRIVER & PASSENGER

These are paint plugs for the front calipers on the Porsche 986 S. You will need 2 of the large plugs, 2 of the small plugs, and up to 5 of the brake line plugs. I printed these in PLA. ... General Print settings (FDM) Layer Height: 0.2 mm Wall Line...

This is a fundamental makeshift substitute for the Porsche special tool used for installing the rear main seal, suitable for Boxster 2.7 engines up to 2004 with the latest 'new style' PTFE oil seal that requires installation at exactly 13 mm depth.

Remixed to fit American size drinks. Can fit a small camelbak water bottle or 32oz soda cup. ... Print upside down with supports.

DescriptionPolygon saving but accurate 3d model created according to real reference. Native format is Cinema 4d R21, model can use Hypernurbs subdivision. Vray version included. Other formats are exported in one resolution. Exported formats 3ds, max,...

This 3D model is crafted on a real car's base with precise measurements and high quality. It closely resembles the original. Supported formats include *.max (for 3ds Max 2008 scanline and V-Ray), *.fbx, *.obj, *.3ds, *.mb, *.lwo, and *.c4d. Note that...

The 3D model was created on real car base. ...It’s created accurately, in real units of measurement, qualitatively and maximally close to the original.