pool pole adapter 3d models

This adapter allows you to quickly swap out your automatic pool cleaner for a vacuum head with rollers, if you need to manually clean areas the automatic cleaner doesn't reach like the stairs. Both ends have a slight taper, so it should be a good fit...

Adapter for mounting the KNX weather station from MDT (model SCN-WS3HW.01) to a pole of roughly 50mm in diameter. The original transparent mounting bracket of the weather station is slid into the adapter and fixed with two screws.Designed for:screws...

The Acurite station used a 3/4" diameter pipe as the pole mount but the WeatherFlow station takes a 1" pole. ... Rather than build a new pole or add a pipe reducer and another stub of pipe, I printed this sleeve which fits over the existing 3/4" pipe.

Garden Hose Pool Jet Syphon adapter This accelerates your syphon flow from the pool... Depending on the pressure it likely drain slightly higher elevation than your draw. Oct 21, 2021 updated male version with a cup instead of flat surface facing...

The more expensive ones (or larger pump kits) come with 1.5 inch tubing and shut offs to make this more manageable (if you buy them extra) but for the stock 1000 pump and 1.25 inch tubing you get on the entry pools (mine is the 15 foot 48 inch pool)...

The more expensive ones (or larger pump kits) come with 1.5 inch tubing and shut offs to make this more manageable (if you buy them extra) but for the stock 1000 pump and 1.25 inch tubing you get on the entry pools (mine is the 15 foot 48 inch pool)...

38 mm VersionThis adapter makes pumping the water out of your pool easier when the water level gets very low. It allows you to get very close to the ground without having to worry about the hose sucking itself to the floor. My print...

The design for this pole-adapter sprayer would match my existing roof rake and its accompanying spray can cap perfectly. It's great that the type of spray cans used here have a simple nozzle trigger - no complicated system is required to work them...

I had bought a bird silo and wanted to mount it on top of a pole that was already in the garden. The pole had a diameter of 32 mm. Simply slide into the post and place the bird silo on top. It is custom made for this specific bird silo:...

The bottom drain socket has a flow restrictor in it, this allows you to use this adapter, https://www.thingiverse.com/thing:5441996, to connect a vacuum to the skimmer and therefore leave the plumbing undisturbed. ...(Simplified remix attached that...

An accessory designed to enable connection of a separate pump to the skimming system of an elevated swimming pool.

A replacement cap designed to fit in the top of a 31mm (ID) monitor arm pole and take the flexible part of an IKEA Janso work lamp (free-standing desk version).

... follow these steps. ...We tested this method using an Intex pool and its accompanying pump. The inner threaded end of the hose screws directly onto the outer threaded part of the pool fitting, where you would normally secure the grid filter in place.

Garden Hose Pool Jet Syphon adapter This accelerates your syphon flow from the pool... Depending on the pressure it likely drain slightly higher elevation than your draw. Attach to the end of your garden hose and latch in front of one of the pool...

The filter that comes with this vacuum doesn't do a very good job of cleaning fine silt in my pool. So, I designed an adapter to use an ultra-fine coffee bag and it works pretty well. If you can find a similar size bag with a higher micron rating...

The filter that comes with this vacuum doesn't do a very good job when cleaning fine silt in the pool. So, I designed an adapter to use an ultra-fine coffee bag and it works pretty well. If you can find a similar size bag with a higher micron rating...

This adapter allows you to connect a standard US garden hose (GHT, FHT) to an Intex above ground pool drain. Onshape: Intex Drain Connector Print Settings Notes: There is quite a bit of overhang in this model's threads (up to 65º in places), but...

I needed to hang my trigger receivers on the light pole below my studio strobes. The receivers I use are Yonguo and have a hotshoe. This allowed for me to hang them under the light. ...I would use a semi-flexible filament, as PLA may crack.

They're using a pole from Amazon at https://www.amazon.com/FeiyuTech-Handheld-Adjustable-Extension-Stabilizer/dp/B074W4NWSR - no idea yet if the model is working correctly, but it probably should be. ...Give it a try if you've got some time.

I decided to install my trigger receivers on the light pole beneath my studio strobes. My trusty Yonguo receivers feature a hotshoe that enables me to secure them firmly underneath the lights. ...To ensure their stability, I opted for a semi-flexible...

To seal up that leaky pool hose end, wrapping it snugly in a thin layer of tape is usually the solution you'll need.

Needed an adapter to fill my pool with air. This is a lot quicker with an air compressor than with a foot pump. Other designs didn't work out as I expected them, so I created this one within a few minutes.</p><p>Best printed with TPU and 15% infill...

Simple prints to attach my Sennheiser SKP100 to a boom pole with Rode NTG4+ are within reach. Two STL files are available: Screw = tight 3/8 hole for screw-in installation Loose = loose 3/8 hole The XLR hole is specifically designed for this...

This attachment was created by the SPU Engineering team to hold a ski pole, though other uses are more than welcome! Designed to be easily 3D printed, flexible filament is recommended for optimal results, but you can also use standard hard filament...

In order to connect the hose (32 mm inner diameter) of a pool vacuum cleaner to the water outlet fitting (goes to the pump). ... The diameter of the thread is 83 mm and the pitch is 2.5 mm.

This is a precise Polar Finder Illuminator Adapter, specifically designed for use with the Skywatcher Star Adventurer system. To secure the adapter properly, simply insert it and then twist it clockwise until snugly in place. ...Upon completion,...

... under its own weight. There is a small window near the overhang that I used to clear out the snow before making this adapter, but unfortunately it was too far away for me to reach with a shovel and I could only clear half of the snow off the edge.

English : I made an adapter for Xiaomi Mi Computer Monitor Light Bar for this mount : https://www.thingiverse.com/thing:4976305 Français : J'ai créé un adaptateur pour Xiaomi Mi Computer Monitor Light Bar en utilisant ce montage :...

... where the latch goes so that battery can be inserted without pressing the release. I used the 5Ah Dewalt 20V Max battery coupled with a CC CV UV (undervoltage protected) step-up adapter to power an electric scooter, converting it from lead-acid.

... net holder. ... Connections: * Large-hose shop vac attachments (I have a Ridgid) * Standard aluminum telescoping pool stick thing * Intex 1.25" hose Printed with PETG for resiliency but I don't think that matters much. ... Zero supports needed!