pool hose holder 3d models

This is a remix of an existing thing here, the pool hose adapter to gardena 32 mm. ... I made the dimensions of the pool hose part bigger to fit on a 40 mm pool flex hose.

A remix of the 1.5inch (32mm) hose connector to give more distance between the hoses to get more heat for the hose for a pool heater

This hose adapter was specifically designed to seamlessly connect a 38mm pool hose with a standard 32mm hose for efficient water flow.

Hose adapter to connect the pool hose to a solar panel.

Pool hose adapter from 50mm to 38mm. ... I am testing wether PVC glue works with PLA and the blue pool hose made of resin connected to a water valve.

Holds the pool hoses when they go to, for example, the solar heaters on the roof. Complete with three suitable screws, I use a trellis screw approx. 55mm long and diameter approx. 4mm. I use PLA and it works thanks to using three screws, but plastic...

This reducer connects the outlet of an Intex swimming pool to an ordinary 13 mm garden hose.

Pool Stick Holder Clip

swimmng pool pipe holder

Bestway Pool Phone Holder

... follow these steps. ...We tested this method using an Intex pool and its accompanying pump. The inner threaded end of the hose screws directly onto the outer threaded part of the pool fitting, where you would normally secure the grid filter in place.

Just a litte adapter to go from a 1.25 currugated pool hose to a 3/4-11.5 garden hose. ...Did this so I can use the pool pump to empty out the pool. Also see my 1.25 hose adapter to taper on the inlet of the pool hose.

I designed this pool hose coupling for ds18b20 temperature sensors. Now i receive the temperature to and from my solar pool heater, via that two sensor connected to an ESP01S with ESPEasy. ...

To seal up that leaky pool hose end, wrapping it snugly in a thin layer of tape is usually the solution you'll need.

Holder for the garden hose 1/2".

This is a compact male pool hose fitting specifically designed for use with 1.5 inch (38mm) hoses. Simply reverse thread the pool hose into the protective cover to secure it in place. To ensure a snug fit and prevent the hose from popping out, I...

I crafted an adapter that snugly fits over 40mm PVC and securely attaches to flexible pool hoses - the same type commonly used by pool cleaners. The design was specifically tailored for diverting plumbing wash water directly into a grey water storage...

This is a support to hold the hose in order to fill the pool without having to hold it. It is suitable for long screws (see detail in photo). Accuracy: We have to retract the empty hose. ...Then once inside the upper circle, turn on the water...

This adapter allows you to connect a standard US garden hose (GHT, FHT) to an Intex above ground pool drain. ... [Onshape: Intex Drain...

In order to connect the hose (32 mm inner diameter) of a pool vacuum cleaner to the water outlet fitting (goes to the pump). ... The diameter of the thread is 83 mm and the pitch is 2.5 mm.

After setting up the pool, I noticed that the inlet was pushing the water stream up out of the water surface because the hose was hanging down due to its own weight. The same effect occurred with the outlet. Therefore, I designed a stabilizer for...

This adapter connects an Intex pool inlet (3rd image) to a standard garden hose click connector (4th image). Use it with a pool vacuum cleaner that requires water for operation, eliminating the need for tap water. As I haven't printed this yet,...

... and refill recently. Not having a sump, I created this adapter to enable me to run my pump while leveraging pressure inside my filter to drain through the garden hose into my front yard. ...Despite leaky hoses, this setup empties my spa efficiently.

FreeCad file included for modification according to your needs Good cleaning *) You can use this as a tip: https://cults3d.com/fr/modèle-3d/maison/pool-vacuum-cleaner-connector-for-bestway-filter-hose or...

This is a pool hose adapter for converting different hose sizes: 32mm - 1 1/4" 34mm - 1 21/64" 36mm - 1 13/32" 38mm - 1 31/64" The hose connectors have outside diameters of 31.75mm 33.75mm 35.75mm 37.75mm so that it fits perfectly on the pool hose. I...

Reduced the thread diameter to fit the Bestway F4030 outlet on my coleman 18ft round pool based on the model from https://www.thingiverse.com/thing:2469017 designed by johannesathome. Include a 4.5mm of the threaded section for test fitting.

Organize your hose on the wall with this simple Hose Holder. ... Its measurements can be found in the photos.

32 mm VersionThis adapter makes pumping the water out of your pool easier when the water level gets very low. It allows you to get very close to the ground without having to worry about the hose sucking itself to the floor. My print settings:PETG0.40...

Set of holders for pool accessories

Universal Pool chalk holder