polisi3d direct drive fan mount

To overcome issues with jams, I implemented a filament guide modification that also incorporated a 12V fan (with hole pattern matching the stepper motor) to counter heat creep. ...The fan is powered by an unused ATX supply socket, and a switch was added...

Having noticed that I've been printing mainly with PLA recently, I decided to enhance the cooling performance of my Bowden extruder by installing two 40mm fans. To do this, I swapped out the M3x40mm bolts for longer M3x50mm ones and secured them to...

I was having problems with jams, so I tried the filament guide, however I believe heat creep was the core problem, so I modified the filament guide to also support a small 12V fan I had (same hole pattern as the stepper motor) and added a switch to...

With it being longer and offset slightly, I found it didn't feel as secure as the stock one did, so I drilled a small hole where the duct overlaps the fan and secured it with a self-tapping screw. This gives me a bit more peace of mind knowing it...

... material since the extruder driver gets pretty hot during operation. it will need two 50 mm fans to work, I also needed to modify my bed size in firmware due to using tiny machine firmware. ... Please comment any suggestions or questions,

However, I also included a blank mount and the STEP files as well in case you'd like to modify it to better suite your needs. The filament sensor and stock mount will just not work with a direct drive setup, so i also created a new mount that...

this mount will let you raise you filament spool mount after install the microswiss direct drive kit and i added an arm to mount a filament runout sensor and this allow the printer to go all the way up and nothing will be on the way link for the...

The CR Touch connector is in a different location than the BL Touch as well as sticks out further to the left. ...This brings in the mount a few mm as well as relocates the connector hole. ...The cable retainer is optional.

The outcome was a double 8x3mm magnet mount that weighed 2g less than the original due to careful trimming. In addition, I incorporated a duct divider to significantly enhance air circulation within the design. The final version (v6) is showcased in...

Converting a Sapphire Pro to a BMG direct drive requires minimal adjustments, preserving valuable build space. For a successful conversion, it's essential to have longer screws available for mounting the linear rail. The BMG is designed to minimize...

A cooler case for Anycubic Vyper Printer, with original dual 4010 fan mount and custom direct drive extruder mount.

This mount includes provisions for attaching a BLTouch sensor and offers additional mounting points on the opposite side for installing a fan or other accessories as needed. One of the images showcases how I arranged the parts for printing, with the...

A remix removing the abl mount as i dont use one

mount for Creality Laser for trianglelab DDE Direct Drive Extruder, it mounts to the heater block fan bonus addon bracket for Digital dial indicator ( cheap one from aliexpress ;) )

couldnt find one so created one

No additional parts neccesary to relocate your extruder. ...There is an arm for a drag chain which is located here >>>> https://www.thingiverse.com/thing:5205630

I took my first stab at creating a component for my 3D printer, eager to get feedback on how I can refine my design and engineering abilities. ...Please point out any areas where I can improve - I haven't tested the part in printing or use yet, but...

To ensure safe installation, it's crucial to place the step-down modules directly in front of the fan within the printhead. If not done correctly, the motherboard may suffer damage. Installation of stepdown modules is performed at your own risk. ...All...

Creality CR10S Pro Direct Drive Mount for BMG Extruder

Set aside fan shroud by removing screw on back Remove track roller spacers and install Direct Drive mount Rotate eccentric bolt on bottom to remove any play Cut bowden tube 8mm above hot end coupler Install extruder top coupler to cut bowden tube...

This is a custom designed extension of the standard BLTouch mount, specifically created to accommodate the impressive Creality Bondtech/V6/Volcano direct drive 40mm hotend fan with extra clearance of 8mm.

This mounts a direct drive extruder to your dpx printer, eliminating the need for the pancake stepper motor. The pancake stepper is inexpensive and reduces weight, but it's not required. I'm utilizing a v6 style hot end that features a fan mount,...

Small remix which adds a fan mount (blower 5015) for better cooling.

Direct Drive Extruder Mount Fits Perfectly on Sapphire Pro Rail Carriage.

Direct Drive for Extruder of Ender 3 v2 with a plate to mount a filament sensor

I modified 2 two mounting holes to fit with Micro Swiss direct drive

Mount for the bl touch on a microswiss direct drive upgrade with hero me gen5.

This is a direct drive spool mount Bowden guide for my system.

I'm testing Bantamount, a free modular mount for CR-10, and discovered that it's relatively simple to modify into a direct drive extruder. ... The results are impressive - it works seamlessly but still requires fine-tuning on the right side to ensure...

This is a custom box mount, fan shroud and endstop triggers I have designed specifically for Prusa i3 MK8 direct drive setups. The setup seamlessly integrates with the Prusa i3 Rework X Carriage, available here:...