polisi3d direct drive fan mount

Remixed BLtouch mount into a CRtouch Mount.Original: https://www.thingiverse.com/thing:5869955One standard height, and one that is extended to drop down 4mm lower.(Crtouch is shorter than BL touch)

... shroud mounting hole. Fit is meant to be tight on the wheel bushings. I had press fit them in with a clamp. UPDATE - New version with a slightly larger hole for the hot-end shroud mount. ...This version the screw head nests inside the hole.

Based on https://www.thingiverse.com/thing:5360818 Reduces the screw length needed for the mount and adds the bltouch arm from the original Klemco cable guide.

Position the mount between the X gantry mount and the X gantry top rollers. Securely insert metal spacers into this mount to ensure a smooth operation. If the rollers do not turn smoothly, add an extra washer in between the mount and the rollers for...

... but didn'T want to use the supplied braket. ...So I designed an holder to clamp directly on top of my extruder motor. ...I used a knive to clean the holes in the holder and then I could screw the supplied screws from the sensor right into the holder.

I remixed Tech2C's remix of the compact bowden extruder, giving it a fresh twist to fit perfectly over the 2040 top rail on my AM8 printer while receiving filament from the rear-mounted spool holder I created.

Designed for fast printing without supports, frictionless spooling, and no unwinding on its own like spool mounts that go through the center of the spool. Needs 4 x 608 bearings, the bearing covers screw onto the threads. It's a tight fit by...

This design leaves two left-most screws available for use, so you have a lot of options for mounting your probe. Print in a high-temp plastic such as Polycarbonate for best results. ... Required hardware: 4x M3 x 14 (M3 X 16 should work too if...

... For securing the mount to the Basaraba Innovations Plate, you'll need two more M3 x 30mm screws. ...Finally, to ensure optimal performance with your stock hotend assembly, make sure to obtain one PTFE tube measuring between 92-94mm in length.

"Motor mount 2-2" is designed to accommodate standard M3 screws (non-countersunk) - the base of the motor has been reinforced to withstand tightening stresses. Engineered in Autodesk Fusion 360. The item featured in the images represents the initial...

---------------------------------------------------------------------------------------------------- I don't have a pancake stepper motor, so I created this mount that can utilize the stock motor effectively. ... You must replace the stock screws with...

The mount clamps the backplate with an M3x10 screw and M3 nut. Not compatible with the original hotend cover. Print on PrusaSlic3r in 0.2mm with 100% infill and 3 perimeters in 0.45mm wide Please comment if you have any recommendations,...

... length. A conveniently integrated mount is also available for a 3.5W Laser from Eleks, which can be easily installed on top of the base plate. ...The laser unit itself can be removed with a single M3 screw for added convenience and flexibility.

I just remixed it to fit the extruder and added a cable mount (pulled from https://www.thingiverse.com/thing:3274980). So this is working great and doesn't require anything to be removed to mount this to the extruder. No rafts, supports, etc...

To Achieve This Modification, You Must Disassemble the Hotend Carriage or Make Cuts While It's Still Mounted - Not Recommended. Modification Requirements: - I Utilized a Dremel to Sever the Top and Bottom Sections of the Metal Backplate (Bottom...

Easily attaches to the Bowden extruder motor mount. It's far easier to rewrap the loom than to thread it back in the meshed sleave, why not use 2 dollars' worth of flexible conduit and the low friction cable holder. ... This version has the M3...

... - it's a lightweight option that fits seamlessly into my setup. After some tinkering, I was able to mount it without any issues during testing. ...Printing TPU at 30mm/s has been working smoothly, and I'm confident I can push speeds even higher.

... soon! ... This design was specifically created for a TronXY X5S that has been converted to a Linear rail on the X axis. I wanted to elevate my Bondtech Extruder and E3D V6 hot end above my other designs, so I needed this mount to lift them higher up.

Inspired by numerous creative designs within this community, I created a bespoke Bowden mount tailored to my Anet A8 printer. As part of an ambitious project, I'm building an enclosure that will house two printers in tandem, one atop the other. To...

... well so far. Fast movements will need to be avoided to ensure stability. Replace original metal bracket with the X carriage, placing plastic mount between tensioner and motor. ...Works with e3D V6 as well as original hotend that came with the kit.

** Inspired by a lot of designs here, I designed a bowden mount for my Anet A8 printer. I build an enclosure and will place 2 printers one over another. So the filament has to be guided from under the table, not from above like in the normal...

I liked this mount for my stock extruder as it was really solid so made one for the titan, so its now mirrored to have the Titan on the left and the stepper on the right and holes adjusted. I run this with a Hero Me setup but my mod of the Gantry...

I created this version because the original design felt fragile and prone to breaking, making me hesitant to attach it to the extruder rod mount without the necessary parts. Since I didn't have access to the original extruder, I decided to simplify...

... tight. Keep infill 80+ to ensure full strength. Do note that it requires wire of extruder motor to be extended so be prepared before mounting. ...Extending cable does not necessary, you can cut wire, join extra cable in between and solder those.

This is a new design for all Creality Ender 3 printers (excluding only Ender 3 S1), CR-10 and Ender 5 Plus with Micro Swiss Direct Drive Extruder along with the original BLTouch metal mount. Inspired from Satsana 5015 Fan Duct and Orbiter Fan duct,...

Remix of this https://www.thingiverse.com/thing:4543524 But thingiverse won't link to it. Adapted for a Titan extruder or clone. I liked this mount for my stock extruder as it was really solid so made one for the titan, so its now mirrored to have...

You will need to rotate the fake titan's mounting bracket so that it matches the pictures (see link below for assembly instructions). If you are still running the stock firmware, there is a guide linked below which may allow you to update the esteps...

This is a remix of the Satsana 5015 Fan Duct from eric_anastas modified to fit "ALL" Creality Ender 3 printers (excluding only Ender 3 S1) and CR-10 with the Micro Swiss Direct Drive Extruder using the "original" BLTouch metal mount. It's been...

Parts needed: (2) M3x12mm, washer, nut for BLTouch mount (2) M3x12mm, washer, nut for mounting shroud to direct drive extruder plate (8) M2x12mm self tapping screw for mounting layer cooling fans (4) M3x12mm self tapping screw for mounting hot end...

I wanted a clean and simple way to mount my BIQU H2 direct drive extruder that kept the stock blower fan, had the BLTouch close to the nozzle, and was compact. This is a complete kit which also includes a filler plate for the original extruder...