pole mount shelf 3d models

Pole mount for HTC Vive headset and controllers is designed to fit a standard shower curtain pole with a diameter of 25mm. This mount includes holders for the charging cables on the side of the controller mounts, keeping them off the floor while the...

... Kelly Egan has on their GoPro adapter which I use to tighten up the threads to the bottom of my camera. ...https://www.printables.com/model/12481-gopro-to-tripod-mount-adaptorPrint Instructions:No Supports needed when printed with the hex end up.

This is a box for my Nixie Clock v2 (from tubeclocks.com). ...I designed it to mount to the 1" gantry pole on my desk behind my monitor that's used to hold my microphone boom arm, DSLR camera, and wireless access point.

Mounted on a 25.5mm pole, this device is engineered to securely attach to a Wire Rack available at Walmart or Amazon. ...Having not put it through a test, I am confident that it can support the weight of smaller screens such as monitors and TVs with...

This is a tripod that fits the hotplates used by TonGi018's backpack camera mount, for those times when you need a longer exposure. It uses three trekking poles as the legs (borrow your buddy's or bring a spare!). ... I removed the locking mechanism...

Pole Mount for Jabra SPEAK410 Speakerphone installed on NavePoint Dual LCD Monitor Stand using a 48mm pole. Clamp features M5 hex nut captures and is assembled with M5 x 20 machine screws from Tekz 45250 Metric Fastener Assortment Box. Print...

I made this because the mount that came with the weather station would not accomodate the pole I chose, even though it DID fit in the bottom of the weather station.I printed this with a 0.8 nozzle at a 0.6 layer height. I used 12 walls.. I forget how...

... Cut the bottom so it would fit the mount. The mount has two holes. You can bore two holes and to use bolts and nuts to hold it on place. Tested with my bike for a day trip. Holds well. Print it standing with brim. ...No supports needed.

There is also a hole in the lower portion for use with a 5mm screw to help secure the mount to the pole. I suggest using PETG since this will need to survive the heat and the cold; dry spells and rainy seasons; fire and ice... well, maybe not that...

A mix of the spray can pole extension and wolf garten adapter - making it compatible with Wolf Garten pole system.

Like the original, use a sharp knife to remove the circular pads once printed. Use some glue to fix the pole mount to the tablet holder. Use 2 M3x20 screws and 2 M3n Nuts. The diameter hole is made for a pole of 32mm. Fusion 360 file is included if...

Just a wall mount for a M10 sisal scratching pole for my cat. It's good for building a climbing wall for your cat :) I used a pole from a cheap cat tree. ...But any M10 sisal pole should fit. I put a locknut into the cutout on the bottom to prevent the...

The original design for this panel mount was inspired by a remix of a popular online model found on Thingiverse at https://www.thingiverse.com/thing:2965429. ...However, that initial design had a limitation - it only accommodated one pair of...

This mount is designed specifically for the Velocitek Speedpuck on a Gennaker pole, and it's built to be used with my Nacra F16 catamaran. To assemble this mount, you'll need 6 x 20mm wood screws and 4 x 30mm M4 Hex screws and bolts. Please note that...

A panel mount for a pair of 15amp Anderson "power pole" connectors. screw some M3x6mm screws into the top for extra strength and insert a piece of 1.75mm filament into the hole to secure the plug. The dust cover should be printed in Flex or...

It's meant to be mounted on a 35mm pole monitor mount, similar to those found on Newegg. I have two of these poles, allowing me to mount it on either side of my desk. Most people probably only have one, so this wouldn't make much of a difference...

The naming convention for these adjustable mounts is as follows: small adjustable - suitable for a 14mm diameter pole, bolted to a GoPro case; large adjustable - suitable for an 18mm diameter pole, also bolted to a GoPro case. Note that you may need...

I have used it for a backpack mount but can be used for Unicorn mount or any other mount where you don't want the GoPro tilting during action as any tilt allows the pole to be visible. This mount is designed to fit 8mmx8mm carbon tube you can buy...

 They have a very good pole mount bracket to attach the AAG CloudWatcher and the optional Anemometer but they do not have a solution to mount the Hydreon RG-9 with them which is the ideal setup.I found a pole mount bracket that looked like it would...

Human: 160° 6-Strand Curved Pixel Pole Engineered Specifically for 12mm RGB Pixels utilizing Boscoyo's pixel strips. Two of these holders are essential, one top and one bottom, secured to 1/2" EMT. The height can be fine-tuned by sliding the bottom...

Painters pole converters are used to transform standard painters poles into cost-effective boom poles that can be attached to a camera's hot shoe. This allows painters and videographers alike to create smooth, dynamic shots without breaking the bank....

RCF EVOX PLASTIC INSERT POLE MOUNT RCF Replacement Part, Enhanced to Prevent Pin Breakage. ... <form action="https://www.paypal.com/cgi-bin/webscr" method="post" target="_top"> <input type="hidden" name="cmd" value="_s-xclick" /> <input type="hidden"...

This is a GoPro mount meant to be attached approximately 50% down the length of a ski pole, creating either a forward-facing mount for "boot height action" or an upward-facing mount for that "selfie" look. The internal diameter measures 18.4 mm,...

This is a Scotty Mount (male end) where you can attach 1-1/4 inch (1.25") 1120 SDR 26 Pipe lengths to create a fishing pole holder for a kayak, canoe, or anything else. I suggest printing with about 75% infill using ABS because it can be cemented to...

Lots of mounts for these base stations, but none that are customizable and at the same time made for poles. As shown on the picture, it is mounted to the post on my On top is a thread to fit the ball mount of the Steam VR 2.0 base station. The ball...

We have a couple of sets of hiking poles that we take with us in our off-road RV and they were just bungee-corded to whatever to keep them from getting in the way. So I designed these clips to be attached to the inside of or storage door, the lip...

The pre-drilled holes on these flags are designed to accommodate a bungee cord that secures the mount by looping it over the tent's frame, preventing the mount from sliding down. The hooks themselves ensure the flag stays locked onto the square...

Based on http://www.thingiverse.com/thing:2066228 by IMakeThisLookGood A 28mm diameter pole serves as the foundation for this design, expertly crafted using Tinkercad to incorporate a ring with an internal radius of 13.35mm. ...The tight fit in PLA...

The solar panel itself is mounted on the weather station pole at a lower height to eliminate getting on the roof. It takes less than an hour of full sun to charge the 18650 fully from empty. The panel is fixed at 30 degrees from horizontal. I...

Holds fine and it'd probably hold much bigger antennas up to 3 sections (like a Diamond GP-9) if you mod the UVS-300 mount itself by drilling holes in the right places for other antennas like this. Designed to also have slots to hot-press M6 nuts...