pocket pussie 3d models

Screw the slipring adaptor into the center hub using stianless screws in the recessed pocket, and then screw the slipring over it, making sure the spinny around part is inside the reel. Route the static wires into the back box. Now glue or tape the...

Hello to everyone who has chosen a Prusa MK3S Clone. The parts that I have put together differ a little from the original MK3S, but this compensates for the few weaknesses. I bought the MK3S from AliExpress and had to find out that the included parts...

So I´ve got this stupid idea for a smaller RC-Benchy for a while. And I figured since it is such a small and simple project I just had to get it done, and in time for 2019 3D Meetup here in Sweden. So here it is, the Mini RC-Benchy, perfect for the...

I used a nail file and then a pocket knife. --Insert the feet block into the legs assembly, so that the feet are flush with the outside edge. The locating pegs on either side should be at the top, while the feet are at the bottom. Align the locating...

For strain relief tie a knot in one of the 2 wires going to each switch or use a very small viptie inside each switch pocket. See pictures above. 3)You can slide the front switch in through the back and then place it on the tray and slide both back...

I searched all over the internet until I found a perfect remix called the “Slack Lack” (Reddit & Thingiverse links). The original designer nnorton00 incorporated these clever sliding-hinges that allow the doors to tuck back inside the enclosure...

Put this magnet in the display magnet pocket. Put display part over the body and test that magnets atract each other. Secure this magnet in place with a drop of super glue. Now is time to glue Olaf lithophane into the display body. Do it according...

The best ones are made like big pockets so users can change the filtering materials as often as necessary. They are easy and cheap to make. Materials for them and decent quality filters can be easily found in any home. Here is a link to a good...

... 5) Install two M2.5 hex nuts in the pockets in the lower case ears. 6) Place the assembled circuit board in the lower case. 7) Install the cover with two M2.5 machine screws and flat washers, assuring that the LED is in the hole in the cover.

A wireless gamepad/controller option is enabled by fitting a holder for a USB ‘dongle’, plus an ultrasonic sensor and an OLED are also fitted to the robot to sense nearby objects and to display the current ‘status’ of the robot.It should be noted...

The following example of a simple code to get you started: ```Python # Python code to create G-code with specific parameters and tool settings import math # Tool settings (parameters should be adjusted according to actual tools used) tool_diameter =...

Plus, fishing the small factory battery out of my pocket every time I needed to change it out was proving to be a bit annoying. Many FPV pilots mount their batteries on the strap of their goggles, but if I was going to use a bigger battery, I wanted...

No more fumbling to find the volume keys on a phone that's tucked into your pocket. Just click. And flip.</p><h5>Technical Details</h5><p>I didn't have a Teensy handy at the time, so I substituted a Keeyees Pro Micro (which Arduino sees as a...

Insert the 4 remaining nuts into the pockets on the head of the Neck. Thread the thumb screws or bolts into these nuts. As the screws tighten the Pads press harder onto the Tuning Pegs increasing their resistance. Glue the Medallion onto the...

(to prevent IR LEDs reflection)Step1: Make the Base section.Open the "Unifi G3 Instant_Case_Base" STL file in Cura.Set the Infill Density to 100% (for best water-resistance).No supports are required for this part.Slice it and in "Preview mode" make a...

That´s the bottom side and must be on the same side as the nose pocket of your goggles. The two long slots are power and volume buttons, head phone and vent openings.</p> <p>I used plastic instant glue on the pillars and the holes in the adapter. You...

Very useful for the "Thumbless" versions where velcro attachments becomes more difficult trying to route a thumb through the palm pocket too. This is an excellent example of thermoform PLA : http://www.thingiverse.com/thing:403001 EDIT 18/09/2014 :...

... is ready! It probably won't quite fit in your pocket, but who would want to hide away such beaty anyway?&nbsp;I hope you enjoyed the model, if so post some pics of yours or just gimme a like if you don't feel up to the challenge! ...Thanks!</p>

In retrospect I'd probably use something other than poplar, as it's not very strong. The risers are attached to the top with pocket screws, and the bottom is attached with regular construction screws. The PC enclosure is mostly made of painted MDF,...

as such the hinge portion may be a little weak and hard to print cleanly, Shouldn't cause an issue if your goal is just showing friends and displaying on a shelf but surviving in a pocket during a convention is a whole different task. If requested I...

The pocket for holding the slim magnet requires that your printer should be capable of modest bridging over a reasonable distance.&nbsp;Parts were designed for printing at 0.3mm layer height, with 0.6mm wall width, but should also print well at finer...

The shorter/wider side snaps into the corresponding pocket on the shaft, and serves to index the tube holder to the shaft. I put a dab of super glue on the nut before snapping it in to the shaft.The magnets should just snap into the holes on the...

Perfect size to hold in your hand or keep in your pocket for use. tradition to consume snuff or other interesting powdered substances - years and years! The whole high society of the 19th century went with elegant snuffboxes - girls and young...

This is a remix of Max Kern's great ZeroBot robot (more on Hackaday.io), with the following changes:HeadlightsGrooved tiresCharging portFront panel holder.Also, thank you Kelly Jordan for the inspiration with your aggressive tank tread.Some extra...

You need to place pieces of wire in the small holes on top of the two side doors and the back door, dymos come into the two round holes of the cockpit wall back, the right hole on the inside of the main body back and in the middle parts of the...

The device packs down neatly to keep the blade flush and out of the way for transport in a bag or pocket, and includes all the tools to assemble itself within the package. The wrench piece for tightening the nuts is 3D printed and also serves to hold...

Watch video here&nbsp;Easy storage of cables, and fits right in the pocket or almost any bag or purse.The pictures explains it all :)It's designed to fit all standard 3mm cables with lightning or USB-C type connector.Assembly is very easy and is done...

Summary Continued:&nbsp;It’s easy to make and small enough to fit in your pocket and take it anywhere you go with dimensions of 6.5 cm x 3.0 cm x 0.2 cm.Link to my partner’s page:&nbsp;Lesson Plan Activity:&nbsp;For this project, our task was to...

I filled the pocket that makes contact with the POGO pin with solder to prevent the wire from slipping back out of the hole and to ensure a good connection, and then super glued the buttons and wires to the plastic. To simplify things, you can...

Also, I removed the nut pocket for the radiator. It was too hard to use with hex nuts. Since Heath generously included his Fusion source file, I remixed it to fix these issues. You'll still need to print Heath's mount lock, if you don't use my...