pocket operator case 3d print

This is a simple case for the "Pocket Operators". You can store a short cable inside it and the operating manual. Have fun ! ...:) www.3Dsection.de

this pocket operator case is a retro model it is elegant design that only 3 parts 1. 1 upper case 2. 23 buttons 3. ... 1 bottom case easy to print is easy to assemble and I want to make it cheap so everyone else can buy it too and have fun :)

(It fits my PO-33 and PO-20) Almost all features of the pocket operators work with the case. The top hanger can be left on or taken off, the input and output jacks are accessible, the wire stand is fully functional, there is a space for the...

Protect your Pocket Operator and make it easier to hold with this sleek two-piece case. It accommodates most plugs for the line-level audio jacks. If not, you can simply remove the top part of the case to facilitate cable ingress. The case does not...

A remake of "Pocket Operator Case (OP-1 Style Keypad)" by justinkowski. I changed the style of the buttons and add some minor improvement to better allocate the operator into the case especially when with the hanger still on. ...

A custom carry case for Teenage Engineering's Pocket Operators, designed with the internal dimensions of ipsofatso's Pocket Operator Sleeve as a starting point. My version features a slightly wider design, a consistent 2.5mm wall width all around,...

This is a case for the pocket operator that has a microphone built-in. Here are the features of my design: LED lights are clearly visible. No need to damage the hanger when using this model. The wire stand remains usable. It's designed with...

A case for the Teenage Engineering Pocket Operator series https://teenage.engineering/products/po Compatible with or without detachable hanger. Depending on printer precision, it may be necessary to rearrange buttons for best fit. ... Feedback is...

This is a case for the pocket operator that contains microphone. Following are the features of my model: - LED lights are visible to the eye. - No need to harm the hanger when using it. - A wire stand is still available for use at all times. -...

If you would like a Commercial License to sell prints made from these designs, please join me on Patreon: https://www.patreon.com/kazitoad This is a fully enclosed case and button set for the Teenage Engineering Pocket Operator series. It protects...

Case for Teenage Engineering's Pocket Operator. This case is compatible with the wire folding stand, and the loop at the top doesn't need to be removed. All LEDs shine through a small hole above each button, and there is a hole to allow the use of...

This is a custom-fit slip-on back case designed specifically for pocket operators with silicone cases. Two distinct versions exist, tailored to accommodate either the 10 series or the 20 series models. ...Notably, the 1/8 TRS jacks are positioned...

Case for Teenage Engineering's Pocket Operator. This case is compatible with the wire folding stand, and the loop at the top doesn't need to be removed. All LEDs shine through a small hole above each button, and there is a hole to allow the use of...

... imperfections. The buttons must be able to move without any resistance. Assembly See instructions on the included pictures. Videos Showing some of the prototypes and the case printed at shapeways. Short demo of 2 pocket operators using this case.

If not, you can simply remove the top part of the case to facilitate cable ingress. The case does not require any hardware to assemble, though after printing you will need to spend some time carefully removing supports from the PCB grooves around the...

This is a case for the Pocket Operator series of synthesizers made by Teenage Engineering. Its main features are: Keys move freely LEDs are still visible Audio sockets accessible with standard sized rubberized jacks Possible to keep the break-away...

... imperfections. The buttons must be able to move without any resistance. Assembly See instructions on the included pictures. Videos Showing some of the prototypes and the case printed at shapeways. Short demo of 2 pocket operators using this case.

you can print the lights on rafts if you want, i did it on the bed itself, but take some transparent filament.They should pressfit into the small holes. Leave the connectors of the buttons on when putting in the case. I noticed when you take of...

https://www.youtube.com/watch?v=-3B4s1c-Kt8 A click-into-place case that uses LEGO pieces for buttons. ...Get the "round plate 1x1" LEGO buttons...

***Updated back plate 25/09/21*** Designed a simple two part PO case, while trying to retain as much of the original style as possible. Features: Keep the metal stand Keep the snap off hanger Access the original buttons for tactile response...

I'm releasing the "shapeways version" of the Pocket Operator case, optimized for SLS printing. Thinner parts with tighter tolerances.The case has been printed by shapeways a fair number of times with good feedback. There was one instance where the...

Simple case for a Teenage Engineering Pocket Operator PO-33 K.O! I don't have any of the other PO models to test with, but imagine it would fit them also. Simple design, slides in/out without forcing (but stays in). ...I printed this several times...

I remixed the Pocket Operator case to add buttons to it and reinforce the case with places for 4 screws to hold it together. ...It takes 4 - 2.5M x 12mm screws (self tapping).

I remixed the Pocket Operator case to add buttons to it and reinforce the case with places for 4 screws to hold it together. ...It takes 4 - 2.5M x 12mm screws (self tapping).

I remixed the Pocket Operator case to add buttons to it and reinforce the case with places for 4 screws to hold it together. ...It takes 4 - 2.5M x 12mm screws (self tapping).</p> Category: Audio

Just like the pocket operators are of minimal design, this case is just big enough to hold and protect a pocket operator, and nothing else. You might even need to shave off the remnants of the hanging tab to get your PO to fit. I recommend small side...

Simple case for a Teenage Engineering Pocket Operator PO-33 K.O! I don't have any of the other PO models to test with, but imagine it would fit them also.</p> <p>Simple design, slides in/out without forcing (but stays in). ...I printed this several...

Crafting a custom fit for my trusty PO-20 was the goal at hand. ...I meticulously cut out precise openings for the controls and power sources, while safeguarding the sensitive buttons from unwanted activation in my pocket.

3D printed Pocket Operator Case

This is a travel case for the pocket operators by teenage engineering. Specifically designed to work with the nice minimalistic case by "The Case" : https://www.thingiverse.com/thing:5317194 I used a personal logo for my version which I photographed....