pocket operator case 3d models

A remake of "Pocket Operator Case (OP-1 Style Keypad)" by justinkowski. I changed the style of the buttons and add some minor improvement to better allocate the operator into the case especially when with the hanger still on. ...

this pocket operator case is a retro model it is elegant design that only 3 parts 1. 1 upper case 2. 23 buttons 3. ... 1 bottom case easy to print is easy to assemble and I want to make it cheap so everyone else can buy it too and have fun :)

Almost every feature of the pocket operators remains accessible even when the case is installed. The top hanger can be left on or taken off at will, the input and output jacks are easily accessible, the wire stand functions fully, there's a...

Case for Teenage Engineering's Pocket Operator. This case is compatible with the wire folding stand, and the loop at the top doesn't need to be removed. All LEDs shine through a small hole above each button, and there is a hole to allow the use of...

Case for Teenage Engineering's Pocket Operator. This case is compatible with the wire folding stand, and the loop at the top doesn't need to be removed. All LEDs shine through a small hole above each button, and there is a hole to allow the use of...

I remixed the Pocket Operator case to add buttons to it and reinforce the case with places for 4 screws to hold it together. ...It takes 4 - 2.5M x 12mm screws (self tapping).

I remixed the Pocket Operator case to add buttons to it and reinforce the case with places for 4 screws to hold it together. ...It takes 4 - 2.5M x 12mm screws (self tapping).</p> Category: Audio

I remixed the Pocket Operator case to add buttons to it and reinforce the case with places for 4 screws to hold it together. ...It takes 4 - 2.5M x 12mm screws (self tapping).

I'm releasing the "shapeways version" of the Pocket Operator case, optimized for SLS printing. Thinner parts with tighter tolerances.The case has been printed by shapeways a fair number of times with good feedback. There was one instance where the...

If you would like a Commercial License to sell prints made from these designs, please join me on Patreon: https://www.patreon.com/kazitoad This is a fully enclosed case and button set for the Teenage Engineering Pocket Operator series. It protects...

... imperfections. The buttons must be able to move without any resistance. Assembly See instructions on the included pictures. Videos Showing some of the prototypes and the case printed at shapeways. Short demo of 2 pocket operators using this case.

This is a case for the Pocket Operator series of synthesizers made by Teenage Engineering. Its main features include: Keys that move freely LEDs are still visible Audio sockets accessible with standard-sized rubberized jacks The break-away hanger can...

... imperfections. The buttons must be able to move without any resistance. Assembly See instructions on the included pictures. Videos Showing some of the prototypes and the case printed at shapeways. Short demo of 2 pocket operators using this case.

One thing I noticed is that when you remove the front case from the plate while it's still warm, it can warp slightly near the screen frame. This gives the illusion that something inside is obstructing its path and makes the upper buttons appear a...

3D printed Pocket Operator Case

Light Guides for Pocket Operator Case Check out this handy guide to creating custom light guides for your Pocket Operator case, accessible via http://www.thingiverse.com/thing:1375818. Watch the video below to see these printed by Shapeways in...

The "v4" version of these buttons features the exact same design as those included in the standard Pocket Operator case. On the other hand, the "v4wide" version has a slightly larger diameter (0.5 mm) and less fillet. However, depending on your 3D...

... ...Compatible with the Pocket Operator case: http://www.thingiverse.com/thing:1375818 The "v4" version are the same buttons as included with the Pocket Operator case. The "v4wide" version of the buttons has a larger diameter (0.5 mm) and less fillet.

Buttons stamped with numbers 1-16 are compatible with the Pocket Operator case. The "v4" version comes with identical buttons to those included in the case. However, the "v4wide" version has a larger diameter of 0.5 mm and less fillet. Printers may...

Lighting up the Pocket Operator Case This video showcases the light guides in action after being printed by Shapeways. These light guides have not been thoroughly tested for FDM printing yet! If you're feeling adventurous and have some transparent...

I've been impressed by this fantastic Pocket Operator case, but one major issue is poor visibility through the led display. So I set out to design a button with a prong that fits snugly into the case holes, hoping it could somehow redirect some of...

Light guides for Pocket Operator case: http://www.thingiverse.com/thing:1375818 The video shows the light guides (printed by shapeways) in action. These have not been tested for FDM printing! If you have some transparent filament, a good printer and...

... tight check your printers dimensional accuracy or break out a file. If you're interested in printing one of these Pocket Operator cases in clear I recommend you check out my other remix which removes the LED holes, resulting in a much cleaner look.

Crafting a custom fit for my trusty PO-20 was the goal at hand. ...I meticulously cut out precise openings for the controls and power sources, while safeguarding the sensitive buttons from unwanted activation in my pocket.

A custom carry case for Teenage Engineering's Pocket Operators, designed with the internal dimensions of ipsofatso's Pocket Operator Sleeve as a starting point. My version features a slightly wider design, a consistent 2.5mm wall width all around,...

***Updated back plate 25/09/21*** Designed a simple two part PO case, while trying to retain as much of the original style as possible. Features: Keep the metal stand Keep the snap off hanger Access the original buttons for tactile response...

This is a travel case for the pocket operators by teenage engineering. Specifically designed to work with the nice minimalistic case by "The Case" : https://www.thingiverse.com/thing:5317194 I used a personal logo for my version which I photographed....

I wanted a custom lid for the PO-20 case, so I changed the 'arcade' text from the original build to a space invaders sprite. ...Love the build, definitely go check it out for your pocket operator.

After removing the interior supports using pliers, the entire case can be stretched over the Pocket Operator. It aims to strike a balance between being flexible enough to provide a good button feel and rigid enough to protect the Pocket Operator...

This is a case for the Pocket Operator synthesizer series from Teenage Engineering. It offers a sleek look similar to the TE silicone covers, with the added protection of a hard case. ... **FEATURES:** * OP-1 style keys make it easy to play * Sleek fit...