playstation mount 3d models

This is a mount for the playstation camera. The camera has a diameter of 28mm. This mount has an inner diameter of 28.1mm (which gives a snug fit for me on my resin printer). ...If you want to use filament, I'd suggest using a diameter of 28.3mm (I'll...

This is a mount for the playstation camera. The camera has a diameter of 28mm. This mount has an inner diameter of 28.1mm (which gives a snug fit for me on my resin printer). ...If you want to use filament, I'd suggest using a diameter of 28.3mm (I'll...

Stand for the latest RUN Playstation 4 (not pro)

Anyway, I liked the way bluecow82's mount was set up but I didn't like how the camera actually sat in the mount and I figured I could shave off some filament by making it narrower on the end. So I stole the little cup section that the camera sets in...

Mount the camera securely on a wall or other vertical surface for a clear view of your surroundings.

I'm aware that there is a very small amount of people out there that still uses this camera, and an ever smaller amount of people that has a need to mount this camera on an internal 90 degree corner - but if you do find yourself in this need, I got...

Support for hanging the PS4 joystick on the wall with playstation logo. ... STL file with wall mount V2 LIZARD custom designs I would appreciate if you follow me on instagram @lizardartandcraft

A self-sustaining Playstation mount for the Ender 3 that demands no extra hardware. This is a remix of Fallguy2006's outstanding friction-fit [support](https://www.thingiverse.com/thing:3088536) for the Playstation Eye camera and tatersalad1999's...

This is a basic adapter for mounting a Playstation Eye to an Oculus Sensor stand. To attach it, you'll need to disassemble the Playstation Eye and remove its base, then secure the camera to the adapter before screwing the adapter into place on the...

I'm using a budget-friendly PlayStation Eye camera with my OctoPrint server, so I designed a mount for the end of the rail to hold the camera securely in place. To ensure it stays put, I attached a small piece of double-sided tape to the bottom of...

I've been using an old Playstation Eye as the camera for our Ender 3 printer for a while, but hadn't found a mounting system that I liked well enough. Hanging it off of the top rail wasn't working so well with tall prints. This remix uses the...

Ps4/ps5 under desk controller mount

Pivotable webcam mount for CTC Bizer. It should also fit on similar models. "Kabelklemme.STL" is used to clamp the cable on the printer frame. A M3x25 Screw+Nut is needed. ...

Pivotable webcam mount for CTC Bizer. It should also fit on similar models. "Kabelklemme.STL" is used to clamp the cable on the printer frame. A M3x25 Screw+Nut is needed. ...Print Settings Printer: CTC Bizer Dual Rafts: No Supports: No Resolution: ...

An inelegant and very personalised remix of this PS Eye Mount. I needed the camera to fit in a specific spot at a specific height as it is difficult to see what is happening on the first few layers of the Lotmaxx SC-10 Shark. It gives a good view of...

An inelegant and very personalised remix of this PS Eye Mount. I needed the camera to fit in a specific spot at a specific height as it is difficult to see what is happening on the first few layers of the Lotmaxx SC-10 Shark. It gives a good view of...

This is a redesign of sorts, I really liked the original design but it took almost 10 hours to print as it required supports all over the place. I thought if I could get this on the bed in a different way I could reduce the print time significantly.

This Playstation Eye accessory boasts robust driver support yet misses out on mounting holes. To rectify this, the bracket is intended for printing in pairs, secured by 4-40 or M3 screws and nuts. Mounting slots along the edges facilitate attachment...

I'm working on a custom design inspired by Drofnas' PlayStation Eye Mount, specifically tailored for my laser engraver's camera module in LightBurn software. ...The goal is to integrate it with the laser burner for enhanced edge detection and object...

... x 480 pixels. I'm thrilled you like this DIY project! To assemble it, you'll need to print five petals and ten PlayStation Eye Mounting Brackets. ... My sincere gratitude goes out to the talented individual who inspired me to create this design!

PlayStation Eye pedestal mount, used to view my prints via Octoprint. ...These cameras are cheap and can be picked up on Amazon for around $13 USD. Amazon affiliate link to playstation eye: https://amzn.to/2WsFcWr

PlayStation Eye pedestal mount serves as a convenient way to monitor my prints using Octoprint. ...Affordable cameras like these can often be found on Amazon for less than seven US dollars.

The fan is held in place by friction, so no extra screws required. The fan mount attaches to one of the screws that hold the Playstation controller port in place. Remove the screw, press the fan into the mount (make sure it's set to exhaust air...

I reworked the Xbox Headset Mount to give it a fresh new look that fits perfectly with my PlayStation gaming setup. The original design is sleek and minimalist, but it just wouldn't blend in with my console's aesthetic. ...So, I made some tweaks to...

Designed a custom mount base for the Playstation Eye to seamlessly integrate with the Modular Mounting System from Thingiverse's https://www.thingiverse.com/thing:2194278 repository. Utilized CAD software Fusion 360 to craft a precision-fit design.

Just a simple remix to allow to hang headset / headphones on playstation 5

I'm eager to try mounting this device to the wall, but I may need to adjust the size of the screw holes to ensure a perfect fit. Print Settings Printer Brand: Printrbot Printer: Printrbot Go V2 Rafts: No Supports: Doesn't Matter Resolution: 0.1mm...

Playstation 4 Camera Tripod Adapter. ... If You Found This Useful, Please Donate What You Think It's Worth To My PayPal Account.

I started with the "Playstation 4 Camera Wall Mount" by gjallarhorn as a starting point, but what I ended up with is something completely different. Taking measurements and general design elements from that original model, I created a camera mount...

I had to attach a PlayStation Eye to my desktop display, so I designed a small holder. This device was crafted using Tinkercad. ...Modify it online at https://www.tinkercad.com/things/nxj9g5ZrWzK.