playseat shifter mount 3d models

... is my first model. Created this to use with the plastic screws from playseat ultimate. I'm able to tighten the central screw without problems now and with no slip from pressing the pedals. ...If wrench feels to tight around screw expand 1mm x an y.

The 3D printed parts necessary for enforcing the playseat challenge for fitting a CSL DD. Assembly: https://imgur.com/a/fHWt52l I've used a 40x3mm aluminum bar. Around ~1,2m or so of it to connect everything in between. The part i called...

This is for an older playseat evolution which had a bad design flaw in which the pedal stand would wobble due to the fact it was only attached at one point. This is a simple shim which remedies the problem. I printed in pla (sideways) with 10%...

I prefer a higher stance than the standard playseat challenge setup, so I fabricate a T connector and foot for a 21mm rod.\r\n\r\nThe custom part features four screw holes for 4mm screws and nuts.\r\n\r\nThis adjustable foot is designed to prevent...

The smartphone stand for the Playseat dashboard seamlessly integrates two sides that snap together perfectly. Measuring 148.8mm x 10mm on one side and 154.8mm x 10mm on the other, the phone housing is designed to fit snugly in place. ...A custom-made...

I am actively redesigning this box as I've realized how little room it currently has for the hardware.** **Additionally, the clamp mount is not the best as it does come a bit loose over time and is not held at the best angle, nor is it at all...

I wanted to experiment with angling the pedals of my playseat challenge like some higher end rigs do. V1 attaches at the far end of the pedals, and would probably work well on hard floors. In my case, the carpet pad made the pedals rock side to...

This is my favorite modification for my Playseat challenge. This cupholder will fit a water bottle (or beer) while doing some Sim Racing. No more awkward reaching to stay hydrated while in the pits! Take a sip of your favorite ale on the front...

but it works :)Both STL files are in this packfor the "Frame gap" and the "Lift kit"I would say the seating position is way better and the total frame stability has probably increased by over 30% Future ideas are gonna be a Shifter stand, and feet...

Check out my gear mount as well: https://cults3d.com/en/3d-model/gadget/playseat-challenge-thrustmaster-th8-shifter-mount It will also fit other frames with 1 inch tubing. Requires two M4x20 mm screws. ...Here's a selection for various projects:...

Feet for the Playseat Challenge. Designed to fit some 50mm x 50mm glider or rubber pads. The glider allow me to easily move my seat around. The front feet can be fixed using zip-ties.</p><p><strong>Important:</strong> I designed the feet of the seat...

This is a can holder for the Playseat Challenge or other brands of racing chair. For anyone wondering why I made this and don't just simply put my drinks on the floor, well, I have a doggo, and he likes to touch things that are on the floor. This...

I wanted a more robust clamp for my Playseat Challenge pedal base. And I still had to be able to fold it.</p><p>And also the base has to be able to put on a angle without putting a lot of stress on the new clamps.</p><p>I made this for M6 hardware...

Take a look at my shifter mount as well: https://cults3d.com/en/3d-model/gadget/playseat-challenge-thrustmaster-th8-shifter-mount This accessory will also fit other frames featuring 1" (25.4 mm) tubing. It requires two M4x20 mm screws for...

... Do not remember which one was for which knob any more though. Also they fit all the other knobs I purchased later, which are not pictured here. Source files are here: https://www.tinkercad.com/things/26UClaJzVPa-fanatec-shifter-knob-sim-rig-holder

Single or a few 8 mm magnets 2 x 688 bearings 1 x spring from a 3D printer 1 x M8 bolt, washer and a nut with bare shaft 2 x M8 bolts and nuts for mounting 14 x M4 nuts and bolts 1 x M4 bold with bare shaft for spring to sit on and also a nut. If...

Hi, this is a Bass Shaker Mount for the Playseat Challenge Seat. ... Thanks for donating paypal.me/Charliethingy

This was made by filling in the space between the two needed mounts on the original version, as well as extending the bracket so it covers the entire length of the 4040 extrusion under the shifter (before the front and back were hanging with no...

Remixed a previous remix for those who need to mount their Fanatec shifters to 4080 extrusion. Use as much infill as you need to make it strong. Recommended 25-40% Made for FANATEC SQ1.5 on 4080 aluminum extrusions. HARDWARE 4 M6 x 20mm to...

I design and print this model to fix my handbrake to my playseat challenge. It can work for a shifter or anything else. You can rotate one piece to the other according to your position in the seat. ... Handbrake :...

... inserted from below, (holes not visible from above) insert the 2 front nuts from above. Then mount the Fanatec DD Pro on the adapter finally mount the adapter on Playseat with 4x M6 screws. ... Variant with labeling and without labeling available

Handbrake mount adapter for Playseat Sensation Pro. I used the Handbrake below: https://www.amazon.de/gp/product/B083QGTGNN/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 For mounting the handbrake plate I used 4 M8x20mm screws with washers. ...For...

... Pedals delivered e.g. ...with the Fantatec GT DD Pro. For mounting on the PlaySeat Challenge. ... Material List: 2 M6 * 30 mm screws (for the front clamps) 8 M4 * 20 mm socket head screws 8 M4 Nuts 2 M5 * 16 mm screws 2 M5 Nuts 2 Washers for M5

My baseplate on the Playseat was moving. Did not matter how hard I tightened the knob in the front of the wheel base plate. Turns out that it do not clamp enough around the metal tube. This piece is to be put under the thick metal base plate. the...

Body shifter

Shifter Fork

FANATEC Shifter

Playseat Challenge Red Locking Part. ...A bit tight to insert, but holds strong and don't need glue.

Shims for 35mm wide U-shape brackets for better grip aroud the playseat tube. ... Standard aliexpress sim hall sensor handbrake.

Playseat Challenge Red Locking Part. ...A bit tight to insert, but holds strong and don't need glue.