playseat gearshift holder 3d models
372343 3d models found related to playseat gearshift holder.
thingiverse
My quick and dirty attempt to merge both the logitech shifter mount and the cheap Chinese handbrake mount remix into one. Since I have both the shifter and a similar handbrake. Opens and prints fine with Prusa Slic3r. It works for now, but I...
thingiverse
This adapter is designed for the VKB Gladiator NXT flight stick to attach to the Mount-It MI-390 TV pole mount. It is far sturdier than any fully 3D printed mount I have tried and with a single thumb screw, the stick can be removed. The adapter is...
thingiverse
Created this so you do not have to print so many parts. Use the 2 hinges from the original design. ... I'm using this construction for a while now and it works very well and stable.
thingiverse
The remix of fr3zno is very decent! The corners of the mount were a bit sharp so I made a small modification by smoothing the corners. ...
thingiverse
This remix extend clamps by 5 cm to 233 cm.I did it because my shifter gets in the way of the backrest.
thingiverse
Not sure if it would work, can't print it for now, if you try it don't hesitate to leave a comment or even better, some pictures !
thingiverse
Fits perfectly under the chair using a M6x25mm bolt in the existing whole under the chair.
thingiverse
I created my own version of the floano design after experiencing issues with slicing theirs. I had several test versions, but they failed to hold up during intense gear changes. This revised model should prove more durable and last longer. I'm still...
thingiverse
This creation is a result of utilizing Tinkercad's capabilities. ...Make any desired modifications directly within the tool at https://www.tinkercad.com/things/0UHWbtg4By9.
thingiverse
I was looking for a way to mount my speakers to my play seat challenge so I made this mount. 20% infill. I used both PLA and PETG because its what I had on the printer. Hope this is useful to someone else. In order to use this you have to...
thingiverse
This simple brace prevents wheel base vertical wobbling. It has been designed to fit my Thrustmaster TX (similar to T300) base but should work with other ones. The wheel plate wobbles even being screwed on the most far from seat position. Because of...
thingiverse
Had to raise seat for 30mm and had some cheap ABS. ...Personally printed 8 walls and 50% infill, one set took 90 grams and 9 hours, but you might print them lighter.
thingiverse
Designed to attach a 2x4 to the pedal tray for custom pedal mounting. Hose clamp method seemed like the best solution and works with a 100kg load cell brake as tested. ...Note the foam has to be removed for these to fit properly.
thingiverse
The original rods didn't line up well with my base plate position so I tweaked the rods a little by shortening them and adding a twist to make them sit flush in the brackets. This solution was needed for mounting my Moza R9 with the base plate in the...
cults3d
This kit was made because I hate dirt inside of my UMG. This set contains: 2 types of sides panels - the longer are for UMG 6x6, the shorter should be for any 4x4 SCX10 II vehicle - NOT TESTED! 2 receiver boxes - S and L - both of them could be...
thingiverse
This is the mount made by jeoje, but I merged the right side of the clamp and the flat surface in one piece. I printed with tree supports and blocked the supports for the holes on the big piece. ... Holes for Logitech shifter.
thingiverse
I Got Fed Up With The Pedals Wobbling, So I Designed This Two-Piece Mount You'll Need: * Four 20-3mm M6 Bolts, Ideally Two With A Flat Head * Double-Sided Velcro Strips Here's What To Do: 1. Print Out The Parts, I Used PET For Its Durability...
prusaprinters
<p>I hate printing and removing supports. Here, i've blanked unsupported holes 0.2mm thick so you woulndn't have to.<br>Just punch through or remove them with something sharp after it's printed. ...No other changes made.</p><p>I'm unsure what license...
thingiverse
This is a pedal platform that is usable for almost any brand of pedal for any type of simulator. I use Saitek rudder pedals and Logitech driving pedals and this base allows me to solidly mount both types. For any other pedals, just make bolt holes...
cgtrader
Don't forget to review all 3D model packs for the best price! Simply click on my username to view my entire collection. This model boasts a fully textured, detailed design that allows for high-resolution close-up renders. It was originally modeled...
prusaprinters
I got so annoyed with the pedals moving, so I created this two-piece mount. ...Originally posted by me on Thingiverse (https://www.thingiverse.com/thing:3230045), now moved here.Required:Four 20~3-mm M6 bolts, preferrable 2 of them with a flat...
cults3d
This model is two parts and is held together by two M6 socket head cap screws and two nuts (Bolt length minimum 40mm). I suggest installing grip tape on the flat surfaces for a secure hold. I also recommend adding one wrap of grip tape to the...