playseat challenge thrustmaster shifter mount 3d models

The playseat challenge comes with two plastic clamps to mount the pedal mount to the chair frame but still allow it to fold.One of mine broke - so this is a replacement. ...Uses M6 bolts - but still allows the chair to fold away.I printed two in PETG,...

This Holder is designed to mount the Fanatec CSL DD Power Supply directly to the Playseat Challenge Racing Seat. The Holder is designed around M4 Threaded Heat Inserts and M4x12 Bolts. I use it, to mount the 5Nm Power Supply. ...I don't know, if it also...

A few straightforward clips keep the playseat challenge neatly folded away. ...I didn't care for utilizing the straps; these simply snap onto place and function perfectly fine.

This clamp reinforces the entire pedal plate and makes it possible to use load cell pedals on the playseat challenge. I printed this in PLA 0.2 layer height. It's best to use supports inside the nut inserts for the bottom pieces. ... necessities for...

I designed this part to attach under the 21mm tube on my Playseat Challenge chair, raising pedal height for a more racing feel during drives. I printed two units and reinforced them with metal plates to boost strength. ...A hole was included in the...

Adding a adapter to the Playseat Challenge on a side area is a fantastic idea. It works beautifully with my E-brake, which I've thoroughly tested. I printed the adapter using PETG infill at 15% and 20%, and it has plenty of strength without breaking....

So, I went through the 10 realistic wheel plate positions for the playseat challenge, and did my best to measure what length and angle each one would need to function. I incorporated that into a dynamic FreeCAD model, where you simply have to enter...

I prefer a higher stance than the standard playseat challenge setup, so I fabricate a T connector and foot for a 21mm rod.\r\n\r\nThe custom part features four screw holes for 4mm screws and nuts.\r\n\r\nThis adjustable foot is designed to prevent...

The 3D printed parts necessary for enforcing the playseat challenge for fitting a CSL DD. Assembly: https://imgur.com/a/fHWt52l I've used a 40x3mm aluminum bar. Around ~1,2m or so of it to connect everything in between. The part i called...

I wanted to experiment with angling the pedals of my playseat challenge like some higher end rigs do. V1 attaches at the far end of the pedals, and would probably work well on hard floors. In my case, the carpet pad made the pedals rock side to...

This is my favorite modification for my Playseat challenge. This cupholder will fit a water bottle (or beer) while doing some Sim Racing. No more awkward reaching to stay hydrated while in the pits! Take a sip of your favorite ale on the front...

Feet for the Playseat Challenge. Designed to fit some 50mm x 50mm glider or rubber pads. The glider allow me to easily move my seat around. The front feet can be fixed using zip-ties.</p><p><strong>Important:</strong> I designed the feet of the seat...

This is a can holder for the Playseat Challenge or other brands of racing chair. For anyone wondering why I made this and don't just simply put my drinks on the floor, well, I have a doggo, and he likes to touch things that are on the floor. This...

... in mind the fit is tight. Next mount the Thrustmaster into the thing, and then the hole arrangement into the profile. IMPORTANT: To print without supports, just put the thing upside down. ...That way the surface will be stronger for the screws.

I am actively redesigning this box as I've realized how little room it currently has for the hardware.** **Additionally, the clamp mount is not the best as it does come a bit loose over time and is not held at the best angle, nor is it at all...

... exactly on the Playseat GearShiftHolder Pro. All you need are M6 screws and nuts :) I printed it with 100% infill for max. stability. If now something wiggles its the playseat base mount, not my print ;P Important: Scale it in Cura to 1000% :)

To see my other sim racing creations, visit: https://cults3d.com/en/3d-model/various/logitech-shifter-mount-for-playseat-challenge https://cults3d.com/en/3d-model/gadget/thrustmaster-t500rs-steering-wheel-adapter...

Single or a few 8 mm magnets 2 x 688 bearings 1 x spring from a 3D printer 1 x M8 bolt, washer and a nut with bare shaft 2 x M8 bolts and nuts for mounting 14 x M4 nuts and bolts 1 x M4 bold with bare shaft for spring to sit on and also a nut. If...

https://www.youtube.com/watch?v=Md1_aOe4Amg https://www.youtube.com/watch?v=P6egd0ZFikw For Thrustmaster T500, use button_case_t500.stl button_case_generic.stl is the generic (universal) base that uses 4 x M5 bolts/screws to secure to your own...

After exhaustive testing, a very solid mount for the Thrustmaster Sparco TSS Handbrake to suit 160mm Aluminium Profile Rig.I wanted something that could stand up to the abuse of hard shifting, and think I've now settled on a solution. ...&nbsp;Please...

Needed to mount my handbrake, took the original file and modified it to fit the sparco TSS mod+ handbrake but left the holes that would accomodate the bottom of the shifterPrinted in PLA on a Weedo X40 with 40% gyroid infillNote the holes for the...

Adding magnets to the shifters on most Thrustmaster rims can be done with 12mm x 3mm magnets. ...Two magnets work well on each shifter, but one magnet per shifter will provide a less intense pull.

Magnetic shifter mod for Thrustmaster. Works on my TS-PC formula rim and 599xx rim. The magnets are designed to be interference fit. ...Use adhesive between any mating surfaces.

Thrustmaster TH8A shifter mod making it more realistic and adding a positive feel. You will need a spring, which can be brought here: https://www.amazon.fr/gp/product/B00A151YKO/ref=ppx_yo_dt_b_asin_title_o07_s00?ie=UTF8&psc=1 I might add...

Base-Fixed Paddle Shifters kit for thrustmaster bases, developed on TS-PC racer and T300rs bases. Useful for rally / drifting or racing with high steering lock cars.   The kit is designed to be compatible with stock wheel-mounted paddles although...

The Human Upgrade Module TH8A Shifter Mod is engineered to enhance the shifting experience by providing a more pronounced tactile feedback.

... screws as well as thumb screws for added convenience and flexibility. Those who appreciate this custom shifter plate may consider showing their appreciation with a small contribution via PayPal at https://paypal.me/PeterMakesThings?locale.x=en_US

Hi, this is a Bass Shaker Mount for the Playseat Challenge Seat. ... Thanks for donating paypal.me/Charliethingy

I design and print this model to fix my handbrake to my playseat challenge. It can work for a shifter or anything else. You can rotate one piece to the other according to your position in the seat. ... Handbrake :...

Playseat Challenge Red Locking Part. ...A bit tight to insert, but holds strong and don't need glue.