playseat challenge thrustmaster shifter mount 3d models

Quick shifter mount I made so I can use my old g27 shifter on the playseat trophy/Logitech g pro seat. Mounts with a ¼" x 2-½" bolt with a matching hex nut on the other side to the seat frame. 1 of each required. Also uploaded the curved washer (hex...

Moza R5 wheel base Power Supply mount for Playseat Challenge foldable cockpit. You can print 2 of this, for aesthetic reasons, but particularly I think it's not necessary once there's no extra force applied on it. Just one is enough. Assembled...

I required a mounting solution for my Fanatec V3s pedals on the Playseat Challenge, so I devised this design. I manufactured this in PLA, yet you could opt for PETG for increased strength. There are two variants: one is tailored for M8 bolts since...

This solution utilizes the remaining hex cap bolts from the Playseat Challenge, making it a "no hardware" design that assumes you've kept spare parts post-installation. Six printed parts are required: four latch onto the frame (two per side) to...

Mount for fixing an Anker USB hub to your Playseat Challenge.Flex the mount slightly and slide the USB hub into it. Fix it with two zip-ties. Done!</p><p>&nbsp;</p><p>You need more simracing parts? ...Hace a look: <a...

The handbrake will sit 25 degrees tilted forward when mounted to a playseat challenge and clears my 300mm WRC wheel on my fanatec CSL DD. Most TM/Logitech wheels are 280mm so you'll have even more room. There is a small pedestal for an arduino board...

I needed something to mount Fanatec V3s pedals on Playseat Challenge, so I came up with this design. I've printed this in PLA, but you could go with PETG for strength There are 2 variants, one for M8 bolt since v3's has 8,5mm holes for mounting and...

* Install ZipTies in mounts * Tighten ZipTies around Playseat Challenge by pulling down then pulling up * Trim ZipTies Requirements: ============ * 1x 5mm Allen Key * 1x 10mm Wrench * 8x ZipTies 5mm * 2x M6x16mm Socket Head Bolt (low profile, so it...

https://mount-it.com/collections/tv-mounts/products/vesa-pole-mount-mi-390 Use code: HONEY15 for 15% off, $25.50 with free shipping https://vkbcontrollers.com/?product=gladiator-nxt Hardware: The top M8 bolt needs to be shortened by about 12mm. ...

I was looking for a way to mount my speakers to my play seat challenge so I made this mount. 20% infill. I used both PLA and PETG because its what I had on the printer. Hope this is useful to someone else. In order to use this you have to...

Print 4 x Mounts Add 4 x M6x20 Hex screw 4 x M6 Locking Nut 8 x 6,4mm washer 8 x Cable Tie 4,8mm

Designed to attach a 2x4 to the pedal tray for custom pedal mounting. Hose clamp method seemed like the best solution and works with a 100kg load cell brake as tested. ...Note the foam has to be removed for these to fit properly.

I've used the Nobsound G2 100 Watt Mono Amplifier to drive 2 bodyshakers using the pre-out subwoofer channel my receiver provides, so I've made a mount for it as well. Note: The whole frame was made from dimensions found in the Amazon listing, so...

I've used the Nobsound G2 100 Watt Mono Amplifier to drive two bodyshakers utilizing the pre-out subwoofer channel my receiver offers, so I've built a mount for it as well. Note: The entire frame was constructed from dimensions found in the Amazon...

Mount the thrustmaster h-pattern shifter onto your 8020-4040-15 series gearbox by securely fastening it with M8 bolts, making sure that all screw holes are properly countersunk to ensure a snug fit and precise alignment.

... to store cups and other small items within easy reach. Mounts securely onto the gearholder, keeping your drinks and essentials organized and at hand. ...Perfect addition to any gaming setup, ensuring you stay focused on the game without distraction.

v2 of the mount, very easy and fast to install with 8 large zip ties and 4 pcs M6 x25 screws the Logitech G29 pedal to Playseat challenge seat&nbsp;Also working with Thrustmaster t300 RS&nbsp;Print instructionsPETG, print 2 times the G code or 4 pcs,...

Steering Column Holder by Playseat

I recently bought a used Playseat Challenge for my son, but it came with the wheel deck mount missing. I had a good look around for a replacement part, and contacted Playseat directly, but had no luck finding one. Therefore, to help others in my...

I used the following hardpoints to mount it on. https://www.printables.com/model/364829-playseat-challenge-diy-hardpointYou will need m3 35mm with nuts. (I used four per side to mount, it is sturdy, but you can choose to use more.) This is for the...

### Installation: V3:   Install ZipTies in mounts   Install rear pedal mounts with M6 Bolt and washer   Option A:     Remove the footplate (3x Red bolts)     Install front mounts   Option B: (Requires 1mm Wrench)     Install front mounts with the...

The pedal board slides down when I close the playseat challenge, so I designed this very simple bracket to hold the T3PA in place. ...Requires a M6x16 bolt I am working on an hard mount to replace the original band with velcro

Universal Playseat Challenge Fanatec Pedals MountsAfter breaking the existing pedal mounts I found on Thingiverse I decided to design my own that would both be more durable and more versatile. ...This universal mount allows you to affix both Fanatec V3...

Recently purchased the Fanatec CSL DD Wheel & CSL Pedals combo intending to mount on my Playseat Challenge. The wheelbase mounted fine, but the pedals had no good way to mount rigidly other than the large velcro strap that comes with the Playseat. ...

Not sure if it would work, can't print it for now, if you try it don't hesitate to leave a comment or even better, some pictures !

Moza SR-P Lite pedal mount for the Playseat Challenge cockpit. So far (a few weeks), it has proven to be sturdy with no noticeable movement in any direction. Designed considering the bars WITH foam cover. Print the parts lying flat. Utilize:...

Clamp to hold the Playseat Challenge chair closed.

I Got Fed Up With The Pedals Wobbling, So I Designed This Two-Piece Mount You'll Need: * Four 20-3mm M6 Bolts, Ideally Two With A Flat Head * Double-Sided Velcro Strips Here's What To Do: 1. Print Out The Parts, I Used PET For Its Durability Against...

I use Saitek rudder pedals and Logitech driving pedals and this base allows me to solidly mount both types. For any other pedals, just make bolt holes where ever necessary and enjoy! ... Related things: VKB Gladiator Mount...

Originally posted by me on Thingiverse (https://www.thingiverse.com/thing:3230045), now moved here.Required:Four 20~3-mm M6 bolts, preferrable 2 of them with a flat headDouble-sided velcroSteps:Print the parts, I used PETG for durability against...