playseat challenge hotas 3d models

I have seen the great ["HOTAS mount for Playseat Challenge"](https://www.thingiverse.com/thing:2865739 "HOTAS mount for Playseat Challenge") project but I did not want to have to use a wooden plate to hold my HOTAS setup. I have also seen the nice...

The primary objective of this mount was to securely hold both components of a hotas setup while retaining the folding and storage capabilities of the playseat challenge. Depending on the thickness of the rubber, there are two versions available for...

This universal mount is designed for the Playseat Challenge. The mount was originally designed for the shifter plate from Advanced Sim Racing. But it can be used for any custom design. The spacing between the mounting holes is 85.2mm. ...

Clamp to hold the Playseat Challenge chair closed.

A few straightforward clips keep the playseat challenge neatly folded away. ...I didn't care for utilizing the straps; these simply snap onto place and function perfectly fine.

A set of mounts designed to rigidly mount the Fanatec Clubsport V3 pedals to the Playseat Challenge. May also fit other pedal sets. ... More Information:...

Mount this versatile clamp securely to a playseat challenge or other objects featuring 25mm tube diameter. I successfully utilized it to attach the power supply. ... Required hardware includes: Two M4x30 screws Two washers designed for M4 Two M4 nuts

I designed this part to attach under the 21mm tube on my Playseat Challenge chair, raising pedal height for a more racing feel during drives. I printed two units and reinforced them with metal plates to boost strength. ...A hole was included in the...

The playseat challenge comes with two plastic clamps to mount the pedal mount to the chair frame but still allow it to fold.One of mine broke - so this is a replacement. ...Uses M6 bolts - but still allows the chair to fold away.I printed two in PETG,...

A set of mounts designed to rigidly mount the Fanatec Clubsport V3 pedals to the Playseat Challenge. May also fit other pedal sets. ...More Information:...

Adding a adapter to the Playseat Challenge on a side area is a fantastic idea. It works beautifully with my E-brake, which I've thoroughly tested. I printed the adapter using PETG infill at 15% and 20%, and it has plenty of strength without breaking....

I prefer a higher stance than the standard playseat challenge setup, so I fabricate a T connector and foot for a 21mm rod.\r\n\r\nThe custom part features four screw holes for 4mm screws and nuts.\r\n\r\nThis adjustable foot is designed to prevent...

This clamp reinforces the entire pedal plate and makes it possible to use load cell pedals on the playseat challenge. I printed this in PLA 0.2 layer height. It's best to use supports inside the nut inserts for the bottom pieces. ... necessities...

The 3D printed parts necessary for enforcing the playseat challenge for fitting a CSL DD. Assembly: https://imgur.com/a/fHWt52l I've used a 40x3mm aluminum bar. Around ~1,2m or so of it to connect everything in between. The part i called...

This is my favorite modification for my Playseat challenge. This cupholder will fit a water bottle (or beer) while doing some Sim Racing. No more awkward reaching to stay hydrated while in the pits! Take a sip of your favorite ale on the front...

I wanted to experiment with angling the pedals of my playseat challenge like some higher end rigs do. V1 attaches at the far end of the pedals, and would probably work well on hard floors. In my case, the carpet pad made the pedals rock side to...

Feet for the Playseat Challenge. Designed to fit some 50mm x 50mm glider or rubber pads. The glider allow me to easily move my seat around. The front feet can be fixed using zip-ties.</p><p><strong>Important:</strong> I designed the feet of the seat...

This is a can holder for the Playseat Challenge or other brands of racing chair. For anyone wondering why I made this and don't just simply put my drinks on the floor, well, I have a doggo, and he likes to touch things that are on the floor. This...

So, I went through the 10 realistic wheel plate positions for the playseat challenge, and did my best to measure what length and angle each one would need to function. I incorporated that into a dynamic FreeCAD model, where you simply have to enter...

I am actively redesigning this box as I've realized how little room it currently has for the hardware.** **Additionally, the clamp mount is not the best as it does come a bit loose over time and is not held at the best angle, nor is it at all...

Hi, this is a Bass Shaker Mount for the Playseat Challenge Seat. ... Thanks for donating paypal.me/Charliethingy

Playseat Challenge Red Locking Part. ...A bit tight to insert, but holds strong and don't need glue.

Playseat Challenge Red Locking Part. ...A bit tight to insert, but holds strong and don't need glue.

I wanted a robust shifter mount for the Playseat Challenge, and used the https://www.thingiverse.com/thing:2914511 as basis, creating a non adjustable and sturdy mount. ...Use three 6mm bolts to mount it to the Playseat.

Remix of the original Playseat Challenge pedals raiser Printed in one piece, no iron brackets needed. ... Can be printed without support.

Provides better grip for moutings on a playseat Challenge or other 25mm sized tubes or rods Print this in soft filament (ninjaflex, soft PLA, TPU...) Printable in vase mode for 0.4mm nozzles

This is a remix of https://www.thingiverse.com/thing:4303004 by Shaykz. ... A holder for the Buttkicker Gamer 2 remote with a pipe clamp for the Playseat Challenge. ... I used some double-sided tape within the clamp.

This shifter bracket is specifically designed to fit the Logitech G29/G923/G920 and Thrustmaster TH8 on the Playseat Challenge racing seat. ... The bracket it's removable by losening the knobs, in order to store the seat without the shifter.

I needed a reliable and robust shifter mount for my Playseat Challenge, so I turned to Thingiverse for inspiration. The https://www.thingiverse.com/thing:2914511 design caught my eye, and I decided to build upon its foundation by creating an...

Here's a mount I designed that allows you to install a 25mm bar onto the leg frames (front or back) of a Playseat Challenge. I used this to attach my own Bass Shaker to my Playseat Challenge. ... Here's a 3 part video on how I did that showing the...