platonic solids kepler 3d models

I used 3-4 perimeters so the walls were solid. I used PETG for the legs holder & feet. This allows the legs to  snap into the body a little more reliably and the foot can hold the bottom ORing. (PETG is more pliable than PLA). But you can print...

This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the models on screens with stl or obj files, it is enough to understand the possibility of printing a model or producing a...

This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the models on screens with stl or obj files, it is enough to understand the possibility of printing a model or producing a...

Model made as 1/8 scale in FDM version and 1/16 in SLS/SLA version.FDM version dimensions: After being printed will stand: 344 mm tall, 162 mm wide, 190 mm deep - with platform; - Connectors should be printed at 100% infill to make them solid.SLS/SLA...

This solid state design of light emitting diodes provides a more reliable, stable, durable, and energy efficient light source over traditional lighting.Beam Angles: When used as a fixed mount fixture, the varying beam angles need to be mounted at...

I have personally used Spiral Vase and a 0.6mm nozzle. However, if you wish to print more than one drawer at the time, or you think the sides are to thin, the following settings can be used to achieve similar results. Perimeters - set to any number...

... them from a piece of material in order to get the nut. In Other words: Take 2 solid blocks, play them over one of these spindles. Copy the spindle one time. Then subtract it from both blocks. This will give you a left and a right nut. ...

on the Wii, he suffers some emotional trauma, stemming from when he was beaten by a group of children in one of his boxing classes.            ABOUT THIS 3D MINIATUREThe model is saved in STL file, a format supported by most 3D printers. This model...

This solid state design of light emitting diodes provides a more reliable, stable, durable, and energy efficient light source over traditional lighting.Beam Angles: When used as a fixed mount fixture, the varying beam angles need to be mounted at...

... ce qui veut dire que même des cables très fins feraient l'affaire. J'utilise des fils en AWG22 parce que j'en avais sous la main. #Versions : 13/07/2019 : Version d'origine (v1) 03/05/2020 : Nouveau support de microswtich, plus solide (v2)

I should have all of my upgrades finished in a day or two and I'll be able to give this a test and make some final decisions for the last build which I'll of in clear green or solid grey so it doesn't turn yellow like the clear resin. Photos have...

You do need the screws in there for strength or the 3D printed part will ultimately break, even if you make the part solid and print it with 100% infill PLA. I didn't try ABS. (I used cap head screws because I had a bunch lying around. Some other...

All parts of connectors should be printed at 100% infill.Scale:  Model made as 1/8 scale in FDM version and 1/16 in SLS/SLA version.FDM version dimensions: After being printed will stand: 255 mm tall, 165 mm wide, 204 mm deep;- Connectors should be...

Repeat step 12 to verify that the connections are solid.Move the USB cable so that ~ 2-4cm of the cable with all its protective layers are inside the bottom part. Use hot glue on this area of the cable to fix the cable to the bottom. Be sure that no...

Multiply by 10 to get the millimetres, which in this case would be 79,577. Open the project file in Fusion 360. On the “SOLID” tab, click on “Modify”, chose “Change Parameters” at the bottom of the drop down. At the top, there are favorited...

- Feet should be printed at 100% infill to make them solid.SLS/SLA version dimensions: - After being printed will stand:54.7 mm tall, 75 mm wide, 58.2 mm deep - In Angry Variant. 57.7 mm tall, 53 mm wide, 52.9 mm deep - In Impressed Variant.
60.3 mm...

Assembly: I used hot glue to attach nuts to the pickup cavity but it was not strong enough, so I used a soldering iron to heat the nut to sink it into the adjuster cavity of the pickup hole and it seems a bit more solid. Had to use shorter M3...

Just search Amazon for Potentiometer Knobs) (https://www.amazon.com/gp/product/B07TB17NLM/ref=ppx_yo_dt_b_asin_title_o09_s00?ie=UTF8&psc=1) - 1 Slide Switch on/off...

There are also useful coat hangers and finger toys.Or just check out all my creations.Print instructionsYou can print it without any support, as long as you leave the cut-angle below 90 degrees.Standard settings will be fine, like infill of 20%,...

This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the models on screens with stl or obj files, it is enough to understand the possibility of printing a model or producing a...

This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the models on screens with stl or obj files, it is enough to understand the possibility of printing a model or producing a...

I used a modifier mesh to set only the inside of the model to 4 perimeters to save material.Avoid Crossing Perimeters: EnabledDetect Thin Walls: Enabled External Perimeters First: True Brim Width: 5mmGenerate Support On Build Plate Only:...

I ended up making two widths of slots to handle the many whims of cable manufacturers. FeaturesFour wide cable slots.Three narrow cable slots.Two USB-A slots.For thumbdrives, adapters, and such.One USB-C slot.Deep tray for holding...

8x5=40… that’s 40lbs of pressure before the 5 springs are compressed further… that’s 18 spools of filament! My bed is still rock solid. No more too low in the front and too close in the back. I also can adjust bed height on the fly and not blind via...

After it extrudes the filament left inside the extruder, just feed in the new spool of filament following it.Slicer SettingsFor the best looking ornaments with a colored background, you'll want the top infill area of the background to be a single...

Designed two clips around it and subtracted it from the resultant solid. Took two cylinders, one 7.5mm in radius, one 3.25mm in radius to create the bolt inset for the suction mount. This top cover took me hours because of the number of faces/edges...

Model made as 1/9 scale in FDM version and 1/18 in SLS/SLA version.FDM version:- After being printed will stand 213 mm tall, 146 mm wide, 264 mm deep;- Connectors should be printed at 100% infill to make them solid.SLS/SLA version:- After being...

General Materials Printed Parts - 8pcs your choice Threaded Metal Rod M8 x 370mm Violin Bridge - will need sanding like all bridges, but also flattening out of the feet Violin Pickup and Preamp - for under bridge (easy to find on eBay or Amazon)...

At this point, I have used the Customizer to successfully print both 4" and 6" sizes.Default Parameters://Display Verbose Output?VERBOSE=1; // [1:Yes,0:No]//UnitsUNITS=1; // [0:in,1:mm]//Pipe DiameterPIPE_DIAMETER=1; // [0:ASTM D2729 => 3 in | 80...

Z door snaps on,  It fits proud, to clear heatsinks and Pi Zero board attached at the back of the Einsy.You should be able to notice that the case and frame are solidly attached, if you have removed the power supply use the support arm I have on...