plantower pms5003 3d models

Use four M2 screws to attach the Plantower PMS5003 to the bracket. **Note** make sure that the screws you chose extend into the sensor no more than 5mm. 2. Use four M2 screws to attache the PCB to the bracket. 3. Use four M3 screws to attach the...

I think if I'd have gone with a shorter wire in my harness it would have fit better. There's quite a few things about the enclosure I would change if I did this again, for now though, it works. The whole system consists of the following hardware:...

i box for an esp32 and a pms5003 airsensor added hole for dht11 sensor

This is a stand for Raspberry Pi Zero, Pimoroni EnviroPlus Hat and optional PMS5003 Particulate sensor: https://shop.pimoroni.com/products/enviro-plus https://shop.pimoroni.com/products/pms5003-particulate-matter-sensor-with-cable

Case for: - WeMos D1 Mini ESP32 - PMS5003 (particle sensor) - SCD41 (CO2, temp, humidity sensor) flashed with esphome and integrated with Home Assistant.

Components: 6x M3 - 4mm screw (Wemos Dual Base mount) 2x M3 - 10mm screw + nut (Particulate Matter Sensor holder) Plantower PMS7003 Particulate Matter Sensor 1x 10kΩ resistor 1x 10µF capacitor Wemos D1 Mini Wemos Dual Base Wemos SHT30 Shield Wemos...

A compact enclosure designed to house both the Plantower PMS7003 particle sensor and the Nano Data Logger, offering users a comprehensive monitoring solution for particulate matter in their environment. ...Learn more about this setup at...

A wall-mounting box for a Raspberry Pi Zero, a Pimoroni Enviro Plus HAT and a PMS5003 particulate matter sensor. When the HAT is directly on a Pi, the temperature sensor on the HAT is heavily interfered with by the heat given off by a Pi (even...

This is a case for a pms5003 sensor and all the necessary parts to make in functional. I tried to make it modular so you kan modify a part of the case for your own components.components used:heltec_wifi_lora_32am2301 temp/humidity sensorPMS5003...

Learn Guide: https://learn.adafruit.com/air-quality-sensor-silo-house/ PMS5003 Air Quality Sensor https://www.adafruit.com/product/3686 PMSA003I Air Quality Sensor https://www.adafruit.com/product/4632 BME280 Sensor...

......The sensor compartment was enlarged to fit a PMS5003 laser particle sensor and BME280 temperature/humidity/dew point/pressure sensor. The front cover has now angled vents to prevent water to enter. Internal holes to hide wiring coming from sensors.

Learn Guide: https://learn.adafruit.com/air-quality-sensor-silo-house/ PMS5003 Air Quality Sensorhttps://www.adafruit.com/product/3686 PMSA003I Air Quality Sensorhttps://www.adafruit.com/product/4632 BME280...

Openlog is self-running data logger module automatically logging serial data from pms5003 particle sensor to TF SD card. You can get it under 3~5US$. (Openlog Serial Data Logger Open Source Data Recorder Naze32 F3 Blackbox ATmega328 Support Micro...

I am a 3D printing beginner so apply your own judgement! Bill of materialsYou will need:Soldering kitA PMS5003 sensor, for PM measurement (AliExpress)The enclosure was designed with the PMS5003 dimensions in mind, but the software works with any...

- Box for use with the Plantower PMS7003 dust sensor. - Box for use with the Sensirion SPS30 dust sensor. - Lid with hole for the OLED display. - Lid without hole for the OLED display. The dust sensor is assembled below the PCB, no screws...

Added pilot holes for cable runs and crafted a custom case for the supported particulate matter sensor (PMS5003). Also included an untested mount for the Raspberry Pi Camera Stand by @atleberg (https://www.thingiverse.com/thing:274111). This build...

## Parts - [ESP32 TTGO T-Display...

We've included different types of mounting holes and brackets for different mounting configurations. Learn Guide: https://learn.adafruit.com/air-quality-sensor-silo-house/ Code on GitHub...

Regarding components, I made a mistake by reversing the PMS5003 color code (red and black were not power). Pin 1 is actually on the right. In my case, the coloring of the schematic on GitHub was correct; it was just reversed for me. ... Eventually, I...

Preliminary Hardware List: SHT31 - Temperature and humidity sensor MS5611 - Absolute pressure sensor DS3231 - Real-time clock (not necessary if using eDOTcore board) MH-Z19 - NDIR Carbon dioxide sensor PMS5003 - Particulate matter 1, 2.5, and 10...