pla printing temperatures 3d models

You'll need: 3 X Ball bearing model 608 3 X Carbon or aluminum 8mm tubes, each 7.5cm long 1 X Dehydrator with a diameter of 32cm 1 X PTFE tube, 20cm long Don't use PLA to print this thing because it can handle heat inside the dehydrator. I made it...

PLA-Tonix is a series of 3D printed Platonic solids that use hinges to open up and show cross sectional geometry. These octahedrons use internal hinges to display two different cross sections. The "square" model displays two square cross sections,...

I tried a lot of released bag clips, but most of them are only working with ABS material since it is more flexible.So I tried to design a clip which also works with PLA.I used a hinge instead of a spring mechanism. The Clip itself is designed to be...

Coil support filament, typically made from polylactic acid (PLA), plays a crucial role in ensuring stable print outcomes and maintaining object shape during printing processes involving 3D printers that employ fused deposition modeling technology. ...

For starters, it can be a fascinating study for aspiring mechanical engineering students of torque versus velocity, as well as spring forces that can be obtained by printing a PLA spring using various infill settings, height and thicknesses. And...

... If using a smaller printer, opt for small_plate and plates 2,4,6,8 instead of full_plate. The pink heart gear above was printed with 25% infill, three shells (two extra in ReplicatorG), at a 200 micron layer height with the skin module enabled.

To print the spring, use one or two perimeter layers without infill - no supports are needed since they're already integrated into the STL file. Additionally, I've adjusted the body hole diameter for better results. For this project, I used yellow...

Spool roller, made to fit 1kg spool of esun pla+.

This is a sample for PLA type filament.

I would recomend devoting this to plastic recycling and to not use it with food preparation - A 0.5" x 4" magentic strips that can be bought from the dollar store or here: https://www.amazon.ca/Magnum-Magnetics-Adhesive-Magnetic-25-Feet/dp/B00114LU8K...

To install it, print out the parts without requiring support (print success may vary). Print with a layer height of 0.2 mm and 100% fill using ABS. Assemble the two parts together by inserting the fan into the slot and fastening it with two 4mm...

Build a shallow wooden box (or print one) a bit smaller than your PLA piece. I painted mine white to match my wallpaper. Cut the LED stripe in fitting pieces and add as many as you like. More LEDs equal more light. Solder all LEDs together and try...

Recently, I visited Protospace fablab in Utrecht, Netherlands, where they used Ultimaker printers with PLA filament. The air quality was much better than my ABS-printing studio. With a PLA roll at hand, I decided to give it a try but encountered a...

I also created a second set with marks on the side to make notes about optimal printing temperature using a thin marker. Left side is to note down temperature in 100°C steps, right side for 10°C steps. Optional to a marker you could also cut out the...

 Print the housing in PLA or ABS, and the cushion in soft TPU.I glued mine together using hardware store epoxy, but I suspect superglue or Gorilla Glue would work just fine.   I used a piece of double sided tape to attache them to the wall...

I 3D printed the engine in PLA, despite its low melting point, and was pleased to find that it performed well without sustaining any damage. The motor's integrity remained intact even after firing, leading me to consider it reusable. ...The engine...

To improve the design, I fixed the belt tensioner and switched to PLA filament. The updated belt is made using kapton-taped paper, blue tape, and a mould for shape. Assemble it on the platform, tighten the belt, and set the heated bed to 35C for...

... due to the potential risk of spring failure and flying debris. This design was created using Sketchup 8 and printed on a Makerbot Replicator 2 with Makerware 2.3.3.42, showcasing the versatility and capabilities of PLA as a printing material.

NEW: see thePLA Cooling Challenge http://www.thingiverse.com/thing:627590 PLA layers need to cool before the next layer is printed. If the layer is small (that is, doesn't take too long to print), it may still be warm and soft when the next one is...

... purposes. Printing: Can print with any infill, I usually use 15%. I have used this connector successfully in several other designs. So if you use this connector in your designs, they will be able to plug in to mine. Which is the point! ...

I struggled with printing this in PLA and the spool snapping at the string holding point, so I revised it to have a smaller opening and rotated it 90 degrees - now I'm about to put it to the test shortly. ...Update: after printing it, I discovered that...

This is a remix of John's excellent uBitX case designed for PET, which you can find here: https://www.thingiverse.com/thing:2732866 Changes include: Closures using 3mm self tapping screws, instead of clamshell style latches. Clearances for fitting...

I printed them with PLA with an 0.8mm nozzle with 0.4mm layers and they work great. With these settings I can print about 104mm of drag chain in 40 minutes. ...Printing them with a 0.4mm nozzle and thinner layer takes longer, but should give you a more...

This one is recommend for spiral vase mode for sure :-) See also : PLA FAN : https://www.thingiverse.com/thing:2630547 BIG DIY 3D Printer : https://www.thingiverse.com/thing:2603668 Easy exchange filament extruder :...

Because it was printed with LW PLA the plane became much lighter. In order to keep the CG in place the battery had to be moved to the rear. There is only room for this if the rear tubes are shortened. Therefore I upload a Remix of the modified...

... also include crank and gear angles, pin dimensions, and holder heights and widths. For printing, the model is optimized with specific settings like layer height (wall) and infill density (E_PLA). ...Note that the DEBUG_GEARS option is set to 0.

It features M/C PLA embossed on the cuff to remind me which filament it's designed for, as I anticipate printing different sized spacers for other spools in the future. ...(M/C = Micro Center) This custom-made spacer is 34mm total depth, ensuring it...

Here is mine at the Seattle Mini Makerfaire last weekend churning out bracelets: http://www.youtube.com/watch?v=nmmUECyz-ek Both of my machines printed continuously both days without any major breakdowns, my TOM giving away ~70 bracelets and my Rep1...

... when they're long. By attaching it to the timing belt, it absorbs vibrations and keeps the belt stable. The design also utilizes three bearings (623ZZ) with a 10mm x 4mm diameter and a 3mm bore, making it suitable for spiral vase mode printing.

PLA FAN 2 Because my PLA fan can only cool from one side, I made a second one that is designed to spread the air 360 degrees around the nozzle without hitting it. This new design has a much bigger housing, taking more room but providing several...