pirated 3d models

The models in my pictures were printed in beige ABS, which is a standard 1.75 mm filament from XYZ manufacturer. I have not tested other filament materials with this design. If printing as a fake sprinkler, I would recommend choosing black; bright...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 pattern_element_overlap = 0 custom_top_port_x_position = -10 custom_bottom_outer_edge_chamfer_radius = .6...

Will require manual tapping. Base Base_Type - The type of base (round or rectangular) Screw_Hole_Diameter - The diameter of the screw hole Screw_Head_Diameter - The diameter of the screw head Screw_Head_Countersink_Angle - Screw countersink angle...

But 100% fan power isn't necessary, so use an lower Value and take the 100% as "headroom" for bridging etc.The bed leveling is done with an single DC42 IR Sensor (I can highly recommend them). Printing and InstallationAll parts can be printed...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_camera_x_position = 0 custom_top_port_corner_resolution = 8...

(Note: If you don’t care about the enclosure being air-tight, you don’t need the straight pieces!) ### Printing the parts The STL folder contains rendered models for a 24"x24" box with 0.118" / 3.0mm acrylic, but the scad files are easily adapted for...

Creality slicer use edit, multiply selected models. PrusaSlicer use cut and past. I'm sure it's possible in other slicing software too. I would recommend printing a few extra as you may damage the edge on a few when inserting them. Assembly: ...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_y_position = 0 custom_top_port_corner_radius = 5 custom_left_port_length = 50 pattern_element_rotation = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_resolution = 8 custom_right_port_corner_radius = 5 custom_back_camera_x_position = 0...

A simple to assemble version of the ER11A Z axis probe that screws onto an ER11A spindle. It has indicator LEDs and can be used to measure and compensate for a bed that isn't flat when engraving, for example a PCB or a curved surface. I use it for my...

This is resistant to everyday wear and tear, but we got warned that rust stains are not completely removable.So a stainless clothes drying rack became necessary.Most commercial ones just have powder-coated steel tubes which rust after some...

I then saw it mention by a Popular Modeller on his Youtube channel and then over the next year the number of downloads went up enormously. So it seems like its time to make some improvements from the original Version 1. DESIGN NOTES For the V1...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

It provides a list of the models. A typical tower includes mostly about 20-30 function calls, generating Lego block elements plus some openSCAD "hand code". If you download the full Doblo Factory code (http://edutechwiki.unige.ch/en/Doblo_factory,...

All overhangs should be 45 degrees or less. Rafts: Not required, unless you experience adhesion issues. License The "Hard Drive Holder" models (.stl) are licensed under the CC BY license by Code and Make. The "Hard Drive Holder" code (.scad) is...

As I'm new to parametric modeling, this solution was done without adhering to full parametric techniques. I'm still learning. The KeyAll HV has two mounting holes, which left 2 open feet for other uses. One foot was left unused, and the other to...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 custom_back_extra_port_y_position = 0 custom_top_port_corner_resolution = 8...

The battery negative is connected straight to the Anderson PowerPole negative and the radio negative.The model includes a plate to put on top of the batteries to ensure nothing gets in and shorts them out.To make the antenna fit inside the box with...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_y_position = 0 stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

Except for the Sunlu mount plate just lay the models flat. The Sunlu mount plate I printed standing upright - even without support (although some minor bridging is needed, but that was no problem)</p><p>As mentioned above, the hygrometers are...

It's also compatible with the Chinese clones of both these models, often referred to as "J-head" extruders. There is a cable guide built into the design which will assist with keeping everything tidy and reduce any stress on the heater and thermistor...

If you are worried about fit and don't want to waste filament, a test print that's just a few layers tall will work well.AdjustmentsThis model was designed in OnShape, which makes it easy to adjust the design; just click here to copy and modify the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

(I have included a model with logo, and one without)Assembly Instructions:Print the box and two clipsInsert bowtie shaped post on clip in to corresponding hole on box, then rotate until the push-clip lines up with the hole.Push the push-clip in to...

Keep doing it until you get a reliable contact. Multi-color printing For printing in multiple colors, you need to slice the model and save it as normal gcode. Then, you have to insert the M600 command. You can do this manually by opening the gcode,...

Please consider checking out our [Masterwork Tools Patreon](https://www.patreon.com/masterworktools/posts) to support OpenForge if you love free models like this, and want to support the community! Also be sure to follow [EC3D Design on...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_x_position = 20 custom_back_camera_corner_resolution = 8 custom_bottom_fillet_resolution = 8 stencil_horizontal_position = 50...