picture frame stand 3d models

A heartwarming gift is a delicate, easel-styled picture holder adorned with dainty hearts and petite flowers on either side, carefully crafted for a cherished relative who treasures a small engraving on thin wood, delicately showcased by this...

<p>Check out the attached instructions.</p>

... Follow these instructions for a customized version: frame lip is 8, frame depth is 7, frame width is 15, stand is enabled with a tilt of 15 degrees, frame thickness is 15, picture width is 180, and picture height is 100.

Another reason I decided to do this was the backing boards of some of my old frames are in pretty poor shape so I opted to make the stand and backing board a single piece. I am waiting on some small backing clips so I can fasten the pieces properly...

If you create an artistic display for your handiwork, such as a picture frame or greeting card, you might need one of these to showcase it effectively. I assembled this item, and it seems to function well. The only challenge is that you'll require a...

&nbsp;Stand is also voronoi design, and will work with the frame horizontal or vertical and is angled 15 degrees.Interior is slotted by 1mm to hold pictures and the slot is located on the side to slide your picture in.Recommend using a rock style...

I beveled the square nobs that pop out from the 2 poles, so it can be printed with no supports.

This is a versatile picture frame holder designed to stand upright, perfect for frames originally intended for wall hanging. It also doubles as a convenient tablet stand. Compatible with larger frames measuring 8 inches by 10 inches or bigger. ... ...

This frame holder stands upright, holding pictures that were meant to hang on the wall. It also serves as a tablet stand. Designed for larger frames, it accommodates sizes 8" x 10" and bigger. ... Print files: Side1_fixed.stl Side2_fixed.stl

The frame's front side makes full use of the 3D printers' capability and is composed of an abstract grouping of small dips and valleys, which all absorb & reflect light differently and create an interesting pattern of shadows.The frame comes with a...

I just thought the rear section required additional reinforcement, so I created a design similar to the one submitted by benny369. ...The main distinction between versions 1 and 2 lies in the orientation of the image itself.

Miniature picture frame (~35 x ~40mm outer dimension) with an integrated stand that works for both portrait and landscape. Area inside the frame fits an 8x10-ratio picture. Picture is held in place by a small ledge. Prints fine without supports in...

Personalized picture frame created especially for Mom on her special day, featuring the little one's own adorable handwriting. ...Holds a cherished 4x6-inch photo and boasts sturdy stand supports that smoothly glide into place.

Picture frame leg, standard size. Picture Support. I had the original leg break on me. This one worked flawlessly. The print quality was not excellent since I printed it with a resolution of 0.4mm. ...I suggest printing at a higher resolution, but for...

Important: The gaps in the model are 0.2-0.3mm wide. It is recommended to check your printer's tolerances before printing this.If the gaps are too small, set a negative XY-compensation setting in Prusaslicer to increase the gap sizes. ...(XY...

Using the following options: * Back Thickness: Set to standard 2 * Panel Depth: Established at a precise 4 * Width Measurement: Accurately measured at 152.4 units * Height Specification: Correctly identified as 101.6 * Selected Plate: Front, our...

http://www.thingiverse.com/apps/customizer/run?thing_id=158157 Instructions Using the Following Options: overlapping sections = 2 Total Height = 127 mm plate type = Front side plate thickness = 4 mm no Stand attached back thickness calibration marker...

Instructions Are Below To Follow This Model: 1) Utilize The Following Settings: • Magnet Diameter Set To 0 • Calibration Also At 0 • Width Established At 101.6 • Position Chosen Is Back Side • Plate Thickness Determined As 2 Units • Border Space...

To replicate this customized model, use the following settings: Width: Set at 177.8 Overlap: At its lowest setting of 2 Height: Precise measurement of 127 units Plate Orientation: Opted for Back Thickness: Constructed with a robust 4-unit thickness...

Hi all,

I Can't Generate This Request

2018 Mom's Day 4x4 Photo Display Cell Phone Holder 5/3 Update: Change Font Size and Include Protective Case

Here is the rewritten text: A versatile picture frame stand that can be customized for any occasion, I designed mine with my college logo proudly displayed. This adaptable design allows for easy scaling to accommodate larger or smaller items, making...

A solution for a broken frame. ... Simple, easy and quick to print. 159mm height 107mm length 10º angle (frame)

Customize your own photo frame with the option of a removable stand for added convenience.

My 7 year old asked for a picture frame, so I made a dozen out of some old pallet boards. Then she wanted it to stand up. Shorter one is tall enough, less plastic, so unless I think of any issues with it, I'll run off a bunch of them. My wife...

This standing picture frame is fully printable; customize it by attaching a photo to the plate or printing directly with your 3D printer. To personalize, upload the "plate" part into an STL editor like Tinkercad, and add any desired shape. After...

A versatile standing frame designed to showcase 2" x 3" photos, offering flexibility to display them either in landscape or portrait orientation with a deliberate tilt of 12 degrees from the vertical axis, depending on personal preference. Work in...