pico remote lutron 3d models

This model was designed with Tinkercad, necessitating the printer to produce separate components that are later bonded together using acetone due to the offset design on its sides, which enables the remote to slide smoothly into place. ...The printing...

Wall plate adapter for Lutron pico remote.

Lutron Pico Remote Wall Plate Adapter is a high-performance device that seamlessly integrates with your existing Lutron system to provide effortless control over lighting and shades throughout your home or office.

I really like these Leviton Screwless covers, but I've been slowly adding smart lights that I want to control with the Lutron Caseta Pico remote. While you could remove the paddle switch and put the Pico remote directly in the wall, here's a solution...

I designed this mount to securely attach the remote that comes with my Lutron P-PKG1W-WH Caseta Wireless 600-watt/150-watt Multi-Location In-Wall Dimmer with Pico Remote Control Kit, or alternatively, my Lutron LZL-4B-WH-L01 Connected Bulb Remote. A...

Pico remote slides onto the pedestal and clicks in to lock in place. The model also has holes on the bottom to allow for recessed rubber bumpers to give the pedestal some grip on the table surface. As pictured, stand was printed without supports at...

Simple Lutron Caseta Pico remote (Model PJ2-3BRL) wall mount holder.Double sided tape or Command Strip would work best to mount.Credit goes to ccmake: https://www.thingiverse.com/thing:5383306/files

Here's a Lutron Pico Remote Wall Mounting Plate Variation where the Remote Slides Down into Place. The design eliminates the need for a magnet in the back, as the remote stays securely held by the mount itself. ...To ensure a snug fit, use support...

This is a sleek wall mount for the lutron pico remote available in various configurations. Adding a magnet to the top back portion will firmly hold the remote in place and allow for easy pull out for on the go use of the remote. Or you can just use...

I got the inspiration for this from roofus4's Lutron Pico Remote Mounting Plate (alternate build), but I wanted to have a finger hole to access the light switch underneath. ...I ended up redrawing the entire project in OnShape and used two 2x6mm magnets...

I'm new to 3D modeling and printing, but this is my take on a Lutron Pico Remote holder that controls a Sonos stereo system. The kids keep losing this tiny remote, so I made a cutout for it as well as a cavity on the bottom/back for another creator's...

I designed a Pico remote mount plate with an open layout, allowing for easy access to the remote control without fully encasing it. The design still provides a secure hold on the remote, yet uses less material, making it simpler to retrieve when...

Compact one-handed pico stand is ideal.

The wall plate was modified to accommodate a Lutron Caseta wall switch, carefully avoiding damage to the heat sink tabs in the process. ...Additionally, reinforcing material was applied to the screw flange to enhance its ability to securely hold screws.

This uses the mounting slot on the back of the Pico remote, so it's easy to attach and remove.The body prints in one piece, and I've included supports which work better than what most slicers will produce. The feet are separate parts and have...

I was installing a bunch of remotes and, of course, came up one bracket short, so here's a replacement with the same basic dimensions as the Lutron Caseta Pico wallplate bracket. This model uses the mounting slot on the back of the remote, making it...

This is a replacement for the Lutron Caseta Pico wallplate bracket. I was installing a bunch of remotes and, of course, came up one bracket short... so here's a replacement that has the same basic dimensions as the Lutron bracket. Unlike other models...

This utilizes the mounting slot on the back of the Pico remote, making it simple to attach and detach. The two components of the stand use a dovetail joint that easily slide together. There's ample clearance in the joint allowing you to grasp the...

This design gets straight to the point, a simple solution to keep my Lutron Caseta wireless lighting/dimmer pico remote safe from falling on the floor. It's a holster for my thick headboard, designed specifically to hold this remote. The key feature...

This is a replacement for the Lutron Caseta Pico wallplate bracket. I was installing a bunch of remotes and, of course, came up one bracket short... so here's a replacement that has the same basic dimensions as the Lutron bracket. Unlike other models...

Pico remote slides onto the pedestal and clicks in to lock in place, 8mm rubber feet fit perfectly in recessed holes on bottom. Printed in PLA 0.1mm layer hight.

Remix of the single remote stand available from https://www.thingiverse.com/thing:2587272 This one provides 2, 3, and 4 remote options.

I've been working on utilizing Pico remotes to control Zigbee lights through Home Assistant, and I wanted some additional wall mounts for the extra Pico remotes that I wanted to install, so I remixed joshcarter's original wall bracket to add the...

I've been working on utilizing Pico remotes to control Zigbee lights through Home Assistant, and I wanted some additional wall mounts for the extra Pico remotes that I wanted to install, so I remixed joshcarter's original wall bracket to add the...

Remix of the single remote stand available from https://www.thingiverse.com/thing:2587272 This one provides 2, 3, and 4 remote options. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: 0.15mm Infill: 100%...

I've been working on utilizing Pico remotes to control Zigbee lights through Home Assistant, and I wanted some additional wall mounts for the extra Pico remotes that I wanted to install, so I remixed joshcarter's original wall bracket to add the...

Here is a wall mount for a Lutron Caseta Pico Remote Control ref. PJ2-3BRL. Can either be screwed on or -preferably- with double sided tape. To be printed upward. ...The dimensions are perfect, neither to snug nor too lose.

Here is a wall mount for a Lutron Caseta Pico Remote Control ref. PJ2-3BRL. Can either be screwed on or -preferably- with double sided tape. To print upward. The dimensions are perfect, neither to snug nor too lose. This object was made in...

The original version of this by JellyTitan was ideal for attaching a Philips Hue Dimmer plate over a light switch, but I also have Lutron Pico remotes that I want to install in a similar manner. By incorporating screw holes for the Pico wall mount...

Base for a Lutron Pico switch designed to secure placement on metal surfaces, such as refrigerators. The pico fits snugly within this base, preventing movement and ensuring stability. Three 3mm round magnets are utilized in its construction. ...Supports...