picatinny rail thumb rest 3d models

picatinny mount designed for mounting on airsoft replicas requires 2 M5x30 allen screws and 2x M5 nuts one version is 45 degrees and the other is 60, both uses the same other half have fun using it, a friend is printing it for me, once tested i may...

For the rail, drill and tap #8-32 thread 1/2" from the bottom of the rail, which is in line with the holes for the front piece and rail holder. ...I drilled a hole every half inch, which lets me move the rail anywhere along the side, but if you want it...

printed at 20% infill on a new creality ender 3, use support and print with the pic rail going upwards.

... ...Equip them with scopes, laser sights, and even sandwiches, all seamlessly integrated onto this commanding rail system. A snug fit is essential, we recommend using high-quality prints to ensure a secure hold that won't budge or slide out of place.

They effortlessly slide beneath the Nerf rail from both sides and are securely clamped in place by any accessory you wish to attach.\r\n\r\nEach rail requires two for proper installation.\r\n\r\nThese adapters are remarkably durable!\r\n\r\nI...

Picanny Side Rail for db9 alloy. Perfect for mounting lasers, small flashlights, and more. ...Print as is on slicer (Vertical for optimal strength)

I remixed the adapter by mshukr1 to fit on Nerf Stryfe. ...I also added some stylish notches in the middle of the rail. ... Watch out for the overhangs.

... side rails. ...Remix now sits about 4mm higher due to the lack of a base on the left-hand side, which was previously rail-free, and I also cut the corner to make up for the shell's shape. ...This modification allows it to screw directly into the shell.

they slide below the nerf rail from both sides and get clamped in position by whatever accessory you want to attach. You need two for each rail. Really sturdy! Tested on a Stryfe. Print Settings Rafts: Doesn't Matter Supports: No Resolution: 0.2 ...

At present, the model is quite rough and was made by performing a boolean difference on Matt Robert's G36 rail design (http://www.thingiverse.com/thing:4757). Next steps include refining separation for the two ends and devising a snap-together...

This device measures approximately 3.3 inches in length and fits snugly onto the Nerf rail. ...For added stability, it's recommended to secure it with either a screw or a strong adhesive like glue.

Not much to say here, just open up your Agitator and replace the BB rail with this one and close it back up. Slots right in. Print at an angle with supports or vertical if you like. ...

I customized the mshukr1 adapter to perfectly fit the Nerf Stryfe. ...I also added sleek notches right down the middle of the rail. ...Be cautious of those overhanging edges.

Remix of TacticalBro's clip on rail. I just filled in a couple gaps so it doesn't split down the middle. ...I find it's more stable this way.

... to have the jam door open. A minor drawback is the noticeable gap at the front end, but the design prioritizes minimalism, anticipating that this rail will serve as a foundation for more elaborate remixes or extensions beyond the jam door.

I wanted to build a mount on my own :) My designs: flash hider: https://www.thingiverse.com/thing:2364355 short rails: https://www.thingiverse.com/thing:2053075 long rail: https://www.thingiverse.com/thing:2053074 fore grip:...

However, to shave off a bit on the weight, I created these printed rails myself.\r\n\r\n-----\r\n\r\nNo printer at home? ...Reach out to me through my Etsy store and I'll be more than happy to print it for...

The ultimate rail: one device that serves as a mighty monarch over all your accessories. Finally, you can proudly mount your trusty scope right onto your bike's frame. Or why not try something new like attaching a flashlight, smartphone, or even a...

This accessory is a sleek rail system that's been designed to pivot and extend in a variety of ways, but I'm not entirely sure what prompted me to create it - maybe I was just feeling experimental and wanted to see how far I could push the design.

Printed upside down on raft.\r\n\r\nResolution: 0.32mm, incredibly fine detail.\r\nRail angle: 4.8°, a slight lean that adds to its appeal.\r\nThe low clamp reaches into the rail, possibly causing issues with certain attachments.\r\n\r\nThis remix...

This is an accessory rail designed for 3D printing, which attaches seamlessly to the Bug-A-Salt. It allows users to easily mount their preferred sights or other attachments. ...The kit includes both a solid part and a downloadable .STL file.

It is the same rail as the first version except that this one is easier to disassemble you will only need a spring (0.3*4*10). 0.3 thickness of the spring. 4 spring diameter. ... 10 length of the spring.

Add two 8mm solid carbon rods, length 200-250mm. ...Don't forget to explore more of my innovative designs by checking out the rest of my collection and stay up-to-date with my latest creations by following me on social media. ...Have a great day!

This rail is versatile and can be easily flipped to accommodate either left-handed or right-handed users. So go ahead and add your $50 light and $50 optic to your $35 blaster - it's definitely worth it! The beauty of this design lies in its ability...

84mm long and slides onto the nerf rail. ...Best held in place with a screw or glue.</p> <h3>Print Settings</h3> <p><strong>Printer:</strong></p> <p>Alfawise U30</p> <p class="detail-setting rafts"><strong>Rafts: </strong> <div><p>No</p></div>...

While they are not quick to attach and detach to the tripods, they allow quick attachment of pic rail accessories such as the Vive controller and HMD. ... 6pcs M3 12mm hex socket caps and nuts (minimum length, M3 14mm suggested) Designed to be...

Print Settings: Printer Brand: RepRap Printer Model: Prusa i3 Rafts: Yes Supports: Yes Resolution: At least 0.2mm Infill: At least 70% Design Process: Creating this design was relatively straightforward, but finding the optimal clearance between the...

Wanted to create a mount on my own ;) my designs: flash hider: https://www.thingiverse.com/thing:2364355 short rails: https://www.thingiverse.com/thing:2053075 long rail: https://www.thingiverse.com/thing:2053074 fore grip:...

... and thread the nut on the opposite side. 9. Move the mount forward in the rail until your bolt is touching the rail. 10. Snug up the bolt. ...You may choose to use Loctite, but the metal-on-plastic interface seems to hold bolts in place fairly well.

After liking the rail I produced for his Snowpeak p-35, my friend asked if I could produce something similar for his Kral NP-03.......and here it is! suitable for most materials, it will require supports. The design is pretty open to print...