picatinny rail riser 3d models

Employee Replacement Option for Worker Side Rails

I hooked up a few rails myself

Pugilist's Pride - Tactical Rail System

Generic side attachment with rail on top.

A replacement Picatinny front block is available for the Tippmann TiPX and TPX guns. ...However, this product is currently unverified; thus, it is considered a work in progress.

... sight, enhancing overall shooting performance and accuracy. ...The process involves carefully swapping out the existing sights with precision-engineered Picatinny mounts, specifically designed for optimal co-witnessing with the red dot sight's reticle.

20 mm standard NATO rail system. ...Made for Airsoft rifle :)

Print 2 pins and one rail.

Short segment of pica tinny rail for reference.

Short segment of pica tinny rail for reference.

A Nerf rail riser that raises an attachment ~2.5cm

I wanted a longer rail cover and I added some alignment features to keep it from sliding on the rail. ...Best printed in TPU.

Set of p-rails for Crosman 1377. Easy to setup. ...Works well!

16 slot rail that will fit an M-LOK/LVOA-C handguard

Keltect CP33 pistol accessory kit including Patcatity rail fore-end component.

The rail's total distance can be adjusted simply by altering its underlying settings.

I extended the rail to match its length to the existing rail on the G36k, ensuring that all three holes align perfectly with the pre-drilled screw holes located at the bottom of the rifle's receiver.

this is a replacement rail for an ACI Maverick.I couldn't find one online so I made one myself. ... :)

You'll be needing a rail clamp as a minimum, along with the mount itself, to get started.

The rail consists of five components: the rail itself and the plates that fit inside. The functionality is straightforward, as seen in the image. M4 screws pass through the rail's grooves, catch on each plate, and then grip the replica from both...

I designed this to secure a picatinny holster onto my dash. This model was created using Tinkercad. You can edit it online at https://www.tinkercad.com/things/02qEjXELAoo. Print Options: Rafts: Not required. Supports: None needed. Resolution:...

Printed with Overture carbon fiber pla. ...Rail is printed upside down with supports 100% infill. 5/32-32 nut and bevel head bolt. ...v1 minor fitting is required.

This is only the rail clamp. ...You will need at least one of these, in addition to the mount.</p> Category: 3D Printing

This is only the rail clamp. You will need at least one of these, in addition to the mount. ... Category: 3D Printing

I have many scopes and ring sets that aren't being used currently and I like having all my stuff organized so I designed these in multiple variations to screw to the wall and store my scopes/ bipods/ scope rings and any other picatinny mount...

It's a 45° Picatinny mount that is strong enough to hold a sniper scope. I designed it because I saw it on Amazon for $14, so I thought it would be cheaper to print.(For me, it worked perfectly, but I don't take any responsibility for broken...

... design boasts a narrow profile. However, a potential issue arises when fitting gas blocks, as .750 gas blocks may contact the rail's bottom. ...The tan parts were designed using FreeCAD, with other components sourced from GrabCAD's library.

190mm long, 20mm wide and hole spacings are 2x 50mm and 1x 40mm. ... Also a rail with a shorter base @1.5mm instead of the 3mm on the original.

I created a custom hex cover for my Rails project because I couldn't find an existing one that met my standards. ...As a result, I designed and built it myself to ensure it aligned perfectly with my vision.

The device is specifically designed to be used in conjunction with a Universal Tactical Interface (UTI) rail, providing seamless integration and compatibility. ...I am pleased with the outcome and consider this to be a satisfactory solution.