picatinny qd mount 3d models

Required: * 4 M3 button screws at 8 or 10 mm length * 4 M3 nuts * 1 M4 screw and nut combo, or picatinny mount screw and nuts UPDATE: Through printing experience, I've learned that 3-4 perimeters are necessary for a smooth finish on lettering,...

For the poors who cannot afford Trijicon. Modeled specifically for the LT100 with corresponding holes and countersinks for lock nuts. Think it uses M3 hardware, I don't remember. ...Sue me.

You'll need two 4x30mm screws and matching nuts to attach the laser mount to your picatinny rail. This was originally based on https://www.thingiverse.com/thing:641947 for the mount and lamp design. ... The momentary switch mount was designed to press...

I'm designing a custom 21mm Picatinny adapter specifically for the Oculus Sensor, making it effortless to aim the sensor with precision when relocating between different areas. The Desk Scene mode can also be used for camera aiming, although it...

... ...The thumb comes into position exactly on the flashlight's button.\r\n\r\nRequired screws :\r\n\r\n - 4 x M4x10mm crosshead screws;\r\n - 1 x M5x25mm (or M5x30mm used with the "Picatinny Flashlight 25_vis.stl" file) hex head screw;\r\n - 1 x M5 nut;

... lumen flashlight (a Surefire replica). Check out its features at http://www.coleman.com/product/high-power-aluminum-led-flashlight/2000009515?contextCategory=1110#.UhPkoZwmWSo. The Picatinny rail has a scale factor to adjust for the ABS shrinkage.

... a 32mm ID that fits over BASR (Bolt Action Spring Rifle) bull barrels, like the Action Army T-10. ...Equipped with Picatinny rails at 0 and 90 degrees, users can attach forward-facing scope cameras and rear-facing GoPros for enhanced performance.

... ...It may possibly accommodate 29mm lights but I do not suggest it. Uses one M5 bolt/nut and two M3 bolts. Recommend nylock nuts for all three. This design correctly conforms to standard Picatinny rails and is intended to a functionally strong piece.

I designed this to secure a picatinny holster onto my dash. This model was created using Tinkercad. You can edit it online at https://www.tinkercad.com/things/02qEjXELAoo. Print Options: Rafts: Not required. Supports: None needed. Resolution:...

... the screws through the holes and attach the accessory at the end of the bracket. Add the acorn nut and GoPro. (hint: the accessory must face the same direction as the teardrop holes on the bracket) Tighten all carefully on the picatinny rail.

... Place the screws through the holes and attach the accessory at the end of the bracket. Add the acorn nut and GoPro. (hint: the accessory must face the same direction as the teardrop holes on the bracket) Tighten all carefully on the picatinny rail.

I utilized an existing GoPro mount found online and modified its placement to enable mounting the camera on the side rails, rather than securing it at the top.

Just my design of a Insta360 Go camera mount for the Diatone TinaWhoop. ...Super Simple.

I printed in PLA and ABS you are free to test any configuration Mine was: ABS 0.2 layer high 35% infill Used supports Mount in 45 degrees Mount pin in vertical with supports

The Bolt Action Sniper Mount is a custom-designed accessory tailored to fit perfectly on the Action Army T-10 Rifle, providing a secure and stable platform for your camera equipment. This mount features a 32mm inner diameter and two-inch long rail...

ACOG Backup Sights Feature an Adjustable Rail Mount for Securing a Trijicon RMR or a Leupold Deltapoint Pro Dot Sight Directly Above Your ACOG Optic.

... it on my HiPoint 9545 / 45ACP Carbine. ...When I fired the recoil caused the camera to progressively roll forward. This design should prevent that. Marked as WIP since I haven't been back out shooting with this mount yet. Category: Sport & Outdoors

Some baby seals needed a weapon light mount for their airsoft toys. This design uses 2 x 3mm 16-20mm length bolts (and nuts and washers) to clamp on the rail. ...Two sizes are included because airsoft toys run undersize.

I wanted to mount a red dot, and have a 25.4mm scope, and 50mm overall space, but the scope ring location and size means I have 13mm and 19mm of space either side of the ring to mount an item to the scope. Fits a 25.4mm scope. ... Requires 4x...

so created this adapter mount, this clamps to the barrel and indexes off of the barrel rib section so it will not rotate. it will either need great bridging or supports to print at most angles. will also need 3 M3 cap screws and 3 M3 nuts. both are...

i designed this as an afterthought for my new mp5 gel blaster but i thought id share the love it hasnt been printed yet but once i do print it i will update, it also needs the m5 nut and bolt but you could get them from an unused go pro mount

... can get the hardware for these on McMaster-Carr (91255A199 & 92362A130) I recommend printing with the 45 degree face on a raft with tree supports turned on for 50 degree overhangs. I also have a model on my page that mounts directly to 10/22.

A single piece was created specifically for a client whose Meprolight sight could not be fitted onto their rifle due to an incorrect mounting arrangement. ...If you require a similar solution, please feel free to contact me for custom design and...

... Airsoft gun, I'm creating a kill cam setup. ...Although it's a common idea, I can't resist the epicness. For the rail mount clamp bolt, I used a shorter GoPro thumbscrew and nut, cutting down the plastic part with a Dremel tool for a suitable length.

Hello everyone, I'm excited to share with you a straightforward mounting system designed specifically for securing airsoft accessories on walls. This easy-to-assemble setup allows you to keep your gear organized and within reach. ...If you have any...

This is a project for an optical mount, inspired by the designs seen at the IWA show in Germany. If you're interested in a similar creation, feel free to reach out. ...I can help with the design and manufacturing process.

This is a phone mount that uses a phone holder from the Dollar Tree that is typically used to hold your phone in your vehicle while attached to a vent. ...I haven't tried it out at the range yet so i'll probably make some changes once that happens.

I manufactured lazerusrm's 90 Degree GoPro Mount for Airsoft guns, but discovered that the GoPro obstructed the Sight view, prompting further research into Whatsacc's solution. Unfortunately, this modification resulted in the GoPro facing downwards.

No one uses these old Contour cams anymore, but if you're a dinosaur like me and still do, this'll let you mount it to some pic rail. ...Only whipped up one side version, if you need something for the opposite side just mirror it or somethin' Three...

This is a mount for the Holosun 509T pattern of micro optics. It's designed to use 30mm M3 hex head capped screws and hex nuts.&nbsp;</p><p>I've tested printing this with up to a 0.6 nozzle and 0.2 layer height- smaller nozzles and layers will work...