pi zero waterproof case 3d models

... significantly. Furthermore, I extended the length of the four retainer posts to ensure a more secure hold on the pi zero board. ...Additionally, I increased the indentation on the lid retainer rail to provide an even better grip on the lid itself.

Made this Thing for my PiZero running my local Blynk Server. Space for the standard Pi 14x14mm heatsink and the GPIO Header (+ Reset pins) Bottom now opened with some hexagon shaped air holes. The feet are 4pcs M3x14 Hex screws and 4pcs M3 Standard...

I made a little RPi Zero W case for my octopi setup since I couldn't find anything specific for it. It made to be mountable using a couple of M4 wood screws. The whole design uses no extra hardware and everything should be able to press fit...

This is a case designed for the OrangePi Zero 2W it's made to be about as small as possible with clips to hold the wifi antenna inside the case.In the design I have included knockouts for a 14mm X 14mm heatsink as well as the GPIO headers if you are...

Hi all,I'm using this to mount my Pi Zero and a HyperPixel 4.0 to my printer.The Bracket I used to mount it on the printer is available in the Fusion file, but it's not very sturdy, so it's probably best not to use it to be honnest.I should probably...

This is a remix of the rpi+raspiaudio case (https://www.thingiverse.com/thing:4709742) to support the use of a ups-lite with the rpi-w (zero) and raspiaudio hat. The ups-lite is a battery and charger system specifically designed for the rpi-w which...

some variants of case

some variants of case

https://andypi.co.uk/2017/05/13/raspberry-pi-sms-to-email-gateway-part-2/

UPDATE: You may wish to print this lovely remix instead, which adds ports for the camera connector and GPIO: https://www.thingiverse.com/thing:1619546/#files An easy-to-print sleeve for the new $5 Raspberry Pi Zero computer prints vertically, with a...

If using 5v 40mm fan, take power from either USB port on Orange Pi or pin headers with appropriate plug or dodgy soldering job. Social Interested in 3D printing? Check out my YouTube videos featuring upgrade tutorials, mods, and other miscellaneous...

* The entire case was re-modeled from scratch, utilizing the sketcher workbench extensively. Please note that this model was created using Freecad-daily 0.17 rev 12495. To mount the orange pi on a battery pack, users can utilize clip-72-16.stl. For...

This case for Pi-Hole utilizes a Pi-Zero W. The first file provided serves as a reference point only and should not be used for direct printing. When using adaptive layers in Cura, the slide-in lid looks particularly sleek. It imparts a smoother...

Here are some links to get you started: * The GitHub repository for this project: https://github.com/andypi/raspberry-pi-sms-email-gateway * The Raspberry Pi website: http://www.raspberrypi.org/ * A great tutorial on using a Raspberry Pi with an...

Its a simple case and its great for non heavy tasks

Added clasps to the case so it be attached to the side of my printer.

... roll. ...The updated build is optimized specifically for the Orange Pi 2 and features output connectors for both HDMI and USB. ...To assemble everything seamlessly, you'll want to have four precision screws on hand - M3 x 12mm will do the trick nicely.

... by stewartallen I upgraded the model with a wall-mounting solution that fits perfectly. ... As it turns out, my Zero gets pretty hot, so I designed a 40mm fan mount that snaps right into place and keeps everything running smoothly.

Hi! ...Here is my case for OrangePi with USB and audio subboard. There is place for WiFi antena and a lot of holes for best cooling. The case is designed for assembly (top and botton side).

PCM5102 DAC: https://www.aliexpress.com/item/1005002992112120.html SSD1306 OLED: https://www.aliexpress.com/item/32804323027.html Pi UPS Lite: https://www.aliexpress.com/item/1005003637992975.html Button board:...

I really liked the case design but wanted the board to fit securely in the case with no movement. I tightened up the top fit as well as put a space above the chip to help with passive cooling. ...Cleaned up USB port opening to mitigate cable issues.

... cutout for fast SD card access. ... Optionally you can use 4pcs insertable m3*3mm nuts for better reliability. Use 4pcs m3*20 screws to assemble the case. I uploaded FreeCAD and STEP files of this case so you can easly modify the thing if you need.

I replaced the honeycomb holes with a hole to fit a 30mm fan. ...Running a 5V fan at 3.3V I get a dramatic temperature drop. For the case bottom, use the original one.

<p>Modified the design from C03D on the verse. ... Reverse engineered the case, added logos and vents. Print instructionsPrint with MMU or as a solid color

I've made it completely compatible with Raspberry Zero, giving you a sleek and modern look. To take it to the next level, I've removed the fan mounting and button placement, allowing for a clean and minimalist design. For all your accessory needs,...

Not to take away from the great work others have posted here for cases, but I wanted a case that I could install a custom antenna. A short stubby one to be precise. My intended use will be to use this as a network wifi bridge for my printer (non...

Here at Make:, we made sure you have a secure way to carry your new mini PC so we created this user-friendly case with no screws or additional parts required! Designed by Make's Digital Fabrication Editor, Matt Stultz. Learn more at Makezine ...

I refurbished an old case I had at home with a fresher look. Built this project for my PiZero running my local Blynk Server. Space is provided for the standard 14x14mm heatsink and the GPIO header, including reset pins. The bottom is now open with...

I really like Farrukh's design, but it was a bit dull for me, so I decided to draw this case in OpenSCAD with just a few modifications. I also created a version with a side fix. It was evening and there was nothing to do. The design caught my eye -...

This is a remix of the Resin.io STEM case. (https://www.thingiverse.com/thing:2275029) I made the top solid (no cut-out for the GPIO). I added standoffs to both the bottom and top where there were none. I added a lip on the top so it just stays...