pi compute module 4 3d models
588841 3d models found related to pi compute module 4.grabcad
Raspberry Pi Compute Module 4 IO Board. ...Also included is the CM4 with eMMC, but without wifi or bluetooth.
grabcad
The antenna assembly that can be purchased for use with the Raspberry Pi Compute Module 4. ... I didn't model the threads where the coax connects to the antenna, but I did use separate parts so the cable can be removed, and I positioned the bolt where...
prusaprinters
This is a fairly straightforward remix of my Raspberry Pi Zero 2020 Bracket that only needed a few numbers to be tweaked here and there to adjust it for the Compute Module 4. I combined one of those (with onboard WiFi and eMMC) with a <a...
thingiverse
Raspberry Pi Compute Module 4 PiTray Mini Case 1 x Raspberry Pi Compute Module 4 1 x PiTray Mini Carrier 1 x Heatsink 55 x 40 x 13.5 mm 4 x Flat Countersunk Hex Bolt M2.5 x 12 mm Sourcekit® PiTray mini https://sourcekit.cc/#/
thingiverse
Raspberry Pi Compute Module 4 PiTray Mini Case with fan 1 x Raspberry Pi Compute Module 4 1 x PiTray Mini Carrier 1 x Heatsink 55 x 40 x 5 mm 1 x Fan 5V Brushless 40 x 40 x 10 mm 4 x Flat Countersunk Hex Bolt M2.5 x 12 mm PiTray Mini...
grabcad
Vertically mounted CM4 DIN rail mounting clips, and assembled model.Original Raspberry Pi Compute Module 4 model:Raspberry Pi Compute Module 4Raspberry Pi DIN rail clip mount:https://www.printables.com/model/225811-din-rail-mount-for-raspberry-pi-4
thingiverse
# Raspberry Pi Compute Module 4 1U Rackmount Enclosure # Introduction This project consists of a [Mini-ITX](https://en.wikipedia.org/wiki/Mini-ITX) adapter and I/O plate to mount the [Raspberry Pi Compute Module 4 I/O...
thingiverse
This is a remix of Glaspedal's Raspberry Pi 4 Compute Module IO Board case. Many thanks to Glaspedal for coming up with the original design. I've split the model into separate STLs for printing, plus I've included variations which allow for a...
thingiverse
Note: The Waveshare Compute Module 4 PoE IO Board comes equipped with four brass standoffs on the bottom of the board. This case was designed to fit the board with those standoffs attached. ...If you remove those standoffs, the board will sit too low...
thingiverse
Since I'm using multiple Raspberry Pi CM4's and IO boards as NAS and docker hosts, I needed something to mount them on, other then the cardboard box they came in. So I made this simple backplate with standoffs that match the mounting holes on the...
prusaprinters
Since I'm using multiple Raspberry Pi CM4's and IO boards as NAS and docker hosts, I needed something to mount them on, other then the cardboard box they came in. So I made this simple backplate with standoffs that match the mounting holes on the...
thingiverse
A simple box to hold your CM4 IO Board from Raspberry Pi. This is very much a work in progress. The lid certainly needs work and the USB slave hole is a bit off. I've included the original FreeCAD file for it if you want to mess around yourself. ...
thingiverse
3D Printed Case for Raspberry Pi Compute Module 4 IO Board without screws
thingiverse
Case for Seeed Studio Dual Gigabit Ethernet Carrier Board for Raspberry Pi Compute Module 4. - No screws or tools needed for assembly - Room for a heatsink and fan. - Carrier board held in place with friction. You may need to apply a bit of...
prusaprinters
<p>I tried to print this once and it didn't quite fit. I gave the card some extra space and organized the code a bit. ...Hope You didn't try the last version.</p><p>Parting the model and turning the lid over in PrusaSlicer works well for me.</p>
prusaprinters
If you want / need use CM4 with PCIe TO M.2 Adapter Pi Compute Module 4 (WaveShare WS-19091) in WaveShare WS-19195 box - you will find that you cannot close original box. This was reason that I created new higher upper part replacement for that...
prusaprinters
... were plugged but still show for looks. Holes on the bottom are for cooling the NVMeafter the air cools the top area. Board can be found at https://www.waveshare.com/product/raspberry-pi/boards-kits/compute-module-4-cat/cm4-io-base-b.htm
thingiverse
Printed case for Waveshare CM4-IO-BASE board. Mounting holes for fan included. Sufficient room to add a heatsink. ... Included spacers with the CM4-IO-BASE board are not always the same, separate spacers might be required for proper mounting.
thingiverse
Low profile printed case for Waveshare CM4-IO-BASE board. Mounting holes for fan included. ... Included spacers with the CM4-IO-BASE board are not always the same, separate spacers might be required for proper mounting.
thingiverse
... ... Remixed from https://www.printables.com/model/107157-dfrobot-mini-router-case to add port labels and additional ventilation. Requires heatsink from PiHut (https://thepihut.com/products/aluminum-heatsink-for-raspberry-pi-compute-module-4-cm4)
thingiverse
This is intended to be an outdoor utility box for the Raspberry Pi Compute Module 4 (CM4) and various accessories, depending on the project. Lots of extra hooks to allow you to go nuts with zip ties. I use it with a CM4, Waveshare CM4 POE board...
thingiverse
Case for the Waveshare Raspberry Pi Compute Module 4 IO Board With PoE. The Top Cover needs hinges and needs printed face down as oriented for smoother finish. This is a remix of one I found on Tinkercad by Stefan Nikolaus. ...
grabcad
This is a basic, uncomplicated inventor's piece for a computational unit.
thingiverse
Compute Module 4 base router using Waveshare's CM4-IO-Base board. The board is maintained using the provided spacers. ... The cover is held on with 6 5x3mm magnets ...
grabcad
Aluminum alloy heatsink for the Raspberry Pi Compute Module 4. Designed by Geekworm. ...Sold on AliExpress.
grabcad
The Raspberry Pi Compute Module 3, abbreviated as CM3, is integrated with Autodesk Inventor 2018's latest version for enhanced functionality and performance.
thingiverse
This setup serves as a testing ground for fine-tuning stereo vision capabilities using the Raspberry Pi Compute Module Development Board. The platform boasts mounting holes designed to secure the development board itself, two camera adapters, and two...