photon ultra 3d models

Accessory rail for the Anycubic Photon Mono X. Print top and bottom separately. Combine with flathead M5x0.8 10mm screws. Rail mounts are 17mm apart, 6mm wide. Mount accessories with flathead M5x0.8 20mm screws. Freecad files included. Holes will...

Hi everyone, Designed a simple ventilation exhaust for my Anycubic Photon using some hose and a 6025 CPU fan. I decided to make use of these components and create something new. I connected the fan directly to the 12v input on the mainboard, and...

Optimized for Anycubic Photon 3D printer. Resin vat center of mass is directly in axis of bottle opening to prevent toppling over. One still must be careful because mass of the vat is much greater then of the bottle. I revised flat planes a bit...

The Anycubic Photon is an excellent printer straight out of the box, but there's always room for improvement. Here are some things that don't quite meet my expectations: * A loud fan in the control area * A loud fan in the printing area * No...

Has cutouts for the onboard Rj plugs, USB for power, external antennae wire, and pinholes for the status light and to hit the reset and setup buttons on the photon. The pinhole for the light is 1.75mm so you can use a piece of clear filament to act...

Vent for Any Cubic Photon This is an upgraded vent lid for the Any Cubic Photon. It is a pretty straight forward print I think I had my settings at 0.15mm layer thickness, I believe I printed it on a raft with supports enabled. The mounting holes may...

Small screws secure the assembled components together, while all electronics are held in place by the LCD support, Photon support, and touch mounts. To establish electrical connections, I employed wire-wrap technology. ...The touch sensors feature a red...

Remove two screws at front left and right corner inside build chamber (somewhat hidden), and two screws on back of Photon above the vent cover. You should now be able to slide the internal part of printer out of the housing to some extent. 4. Open...

A mod to reduce the z-wobble with the Anycubic Photon (zero). The idea is that the lead screw nut can freely move the x-y plane, but is constrained in the z-direction. Contains the following parts: - Guide for the lead screw nut (largest part,...

Developed in 2008 based off the prototype Photon, this was a sort of mix of worlds in trying to make a standard car with some minor changes work for both foam and rubber tire racing. The car ran extremely well on asphalt with overseas success plus...

Nice design, unfortunately the barrel of the Photon M3 does not fit because of the lugs on the bottom side. I have modified the design accordingly. Revision 1 (file with B extension.) This one is more open en you don't have to slide the vat from...

I grabbed a second hand anycubic photon from my local cash converters. they claimed the machine was barely used and basically new. I have run a few tests now and many failed attempts at getting this right but finally starting to get some prints. ...

I have a resin 3D printer, an Anycubic Photon Mono 4K specifically. When I print things, the buildplate remains wet and a lot of resin gets wasted when I remove the part and clean the plate, so i designed this drainer so to make the plate drain...

I printed the parts using my Photon 3D printer, applying standard tilt and auto-support settings at a 0.1mm layer height, resulting in a smooth finish. To assemble the unit, I first removed the two screws from the fan housing and took out the...

Designed to use 18mm conduit / cable tidy pipe (think that's what its for) the fan I've used is an oddball 24v cooling fan that I had knocking about, but the fan funnels added here are for a standard 12v 120mm computer cooling fan (easy to run a low...

Remix to fit my Photon S power supply, type TDX Power TDX-1206000. Made specifically for smaller power supplies, with added vent holes to ensure efficient heat dissipation. As an electrical engineer, I strongly believe that PSUs should be given...

Since the Photon Zero is kinda new, I designed this to let more resin drip back in over time than wiping it away with tissue. Resin is pretty expensive. I also included the F3D & STEP files. There's a canvas there with an approximate reference to...

The BOREALUS Photon starship sails with sunlight on large mirrors, named after a Greek wind god. This innovative spacecraft harnesses radiation pressure for propulsion and draws comparisons to sailboats, using solar light. High-energy laser beams...

This is an upgraded door handle designed specifically for the Anycubic Photon MSLA printer. It features a reliable nut trap that securely attaches the handle to the door via an M4x12 screw and M4 nut, ensuring a snug fit every time. To enhance...

# Anycubic Photon Mono "Tray Dripper" This "thing" is a bracket that sits on the top of the build platform and allows you to easily tilt the platform to assist the resin in dripping off :) ### A update will be coming soon to correct the issue of the...

Two easy solutions to eliminate hazardous fumes from your space when operating the Anycubic Photon.\r\nOne option involves installing a removable ventilation unit at the back of the printer using screws instead of the standard factory-installed cover...

Exhaust system for Anycubic photon Mono SE. 100mm hose connection You can choose to print the hoseadapter including fanhousing as one part (Adapte_100mm.stl) or splited I printed the parts as splited so i didn't need any supports. As fan i used an...

Developed in 2008 based off the prototype Photon, this was a sort of mix of worlds in trying to make a standard car with some minor changes work for both foam and rubber tire racing. The car ran extremely well on asphalt with overseas success plus...

... Assembly see under Post-Printing Use: Install tripod into Photon, Resin tank should be in the printer, can also be filled. Loosen all three adjusting screws, lift aluminum plate to top, tighten one adjusting screw so that the plate stays on top.

https://www.thingiverse.com/thing:5356420 I used the Photon Sword by d4rk0s: https://www.thingiverse.com/thing:409762 for the outside design I used 3DPRINTINGWORLD's lightsaber: https://www.thingiverse.com/thing:3668138 for the blade and I used my...

Legacy file are available at http://www.thingiverse.com/thing:2277397 The Photon Printer started out as a quick weekend project then quickly escalated when I saw that there was room for improvement in the current designs. Designing the components...

This is the STL file for modifying the main part of the Anycubic Photon Z-Axis. The part should be made from aluminum, but I'd love to see someone try using a strong 3D printed material. This video will show you how to complete the modification:...

My inspiration came from the following things: Heater enclosure Photon Mono X: https://www.thingiverse.com/thing:4957808 ANYCUBIC MONO X HEATER: https://www.thingiverse.com/thing:4785435 Lid Spacer Anycubic Photon Mono:...

I designed my own model based on the ANYCUBIC PHOTON Easy Leveler by wundel, thing:3096818, but remade it in OpenScad. The new design uses captive M3 nuts for the clamps and features cone-tipped grubs screwed into them. I enlarged countersunk holes...

As an addition to my other creation, the Photon Gasket, you will find this tiny gutter handy if you don't want any leaked resin to simply drain off the front of your device onto the touch panel. Some kind of vessel placed at the open end will prevent...