photon mono x 3d models

frame for standard bath photon

This is a support for avoid to find a free place for the top cover. ...It simply hang to the printer itself. Printing: PLA, no spécial think. Here is the full desciption on Instructables : https://www.instructables.com/Photon-Mono-Top-Cover-Support/

Wanted a bracket to hold the build plate for my Photon Mono at an angle to assist with draining any resin off before cleaning. Looked at a few, and decided to just build one. ... Build plate is held at 35 degree, and centered over the resin tray

Build plate drain platform to support the latest model of ANYCUBIC Photon Mono 4K with Die Casting Cantilever. The hanger has been designed to clear the resin vat and does not need to be removed in order to print. ... Version 2 has been modified to...

This is a vertical hanger for the Anycubic Photon Mono M5S. I am assuming it would also work for the M5 too. ...This hanger is really only good for prints with a built plate to top height of about 80mm or less, otherwise it may drip outside of the vat.

Made another cover for the Photon Mono because the others i found here on Thingiverse didn´t fit or it wont pass the screws which holds the vat in place when i tried to put the lid on. ...The distance from gap to gap on the lid is 15.2 cm.

Made another cover for the Photon Mono because the others i found here on Thingiverse didn´t fit or it wont pass the screws which holds the vat in place when i tried to put the lid on. ... The distance from gap to gap on the lid is 15.2 cm.

Couldn't find a buildplate drain bracket for the Photon Mono SE that can be left on during printing (it seems like the regular Photon buildplate attachment is really close in size but I'm not sure). Holds buildplate at an angle so all the resin drips...

**https://www.printables.com/model/643200-anycubic-photon-mono-2-vat-cover** Made a vat cover/lid for the new *Photon Mono 2* since i couldn't find one. Enjoy. There are two models: one titled **VASE** and one titled **RIGID**. The **RIGID**...

With this you can be sure you only throw away absolutely empty bottles :) This was made for Anycubic Photon Mono 4k - I don't have meassurements of any other models to confirm if it would work there. Feel free to remix for your model. It was also...

Adapter for Photon Mono buildplate to mount on Anycubic Wash & Cure Station. Uses M6 screws, like the original. I used a height of 15mm instead of 12mm of the original mount on the Photon Mono. It makes everything a bit more stable and for me...

It simply hang to the printer itself.Printing: PLA, no spécial think.Here is the full desciption on Instructables : https://www.instructables.com/Photon-Mono-Top-Cover-Support/Print...

This lid also WORKS with Photon Mono -V3 fix overall fit (needs a well-tuned printer so print fits properly) -V2 fix corners and other small details -Add no logo version This resin vat lid keeps dust and other debris out of your resin tank and also...

Hello, I have created a screen cover with hinge for Anycubic Photon Mono 4K, so that at night the light from it does not annoy me when I sleep. The thickness is like this because I used black resin from Anycubic and it came out that in this...

Wanted a bracket to hold the build plate for my Photon Mono at an angle to assist with draining any resin off before cleaning. Looked at a few, and decided to just build one. Build plate is held at 35 degree, and centered over the resin tray. ... V2...

... cut cable tie or even resolder it. It is up to you.For better result you could also seal the printer main lid joint with sealing tape or some other sealing materials. Printer Brand: AnycubicPrinter:  Photon Mono SE Category: 3D Printer Accessories

:-)__ ---------------------------------------------------------------- Inspiriert durch das Design "Anycubic Photon VAT Lid by KayIOA" habe ich einen Deckel für den Resinbehälter meines Anycubic Photon Mono entworfen ... mit einem Logo. Im ersten...

Hi!I made this for my Anycubic Photon Mono SE. This is the 4th iteration and can be printed at very high speed and still be functional. Settings I used:Line Width: 0.6mmLayer Height: 0.28mmSpeed: 120mm/sMaterial: PLASupports: No!You can use...

One of the things I miss about the original photon was how easy you could rotate the bed by 90 degrees after printing to allow hollow parts to drain fully, this design achieves the same thing but at a angle of 88 degrees to keep the top of the build...

This is a minimal extruding replacement for the back vent plate of the Anycubic Photon Mono SE 3D SLP printer with a 4" vent that can be used with a 4" Inch Inline Fan to vent the fumes. NOTE: This item hasn't been printed or tested yet, but the...

I've seen several Photon Mono adapters for Wash & Cure, but I didn't feel like twisting and unscrewing the mount every time, and I also wanted to use the metal bracket that came with the kit rather than throw it away. The difference with my adapter...

I was looking for a cover for my vat but only have my Anycubic Photon Mono 2 (no filament printer).All the lids I found were to large (even angled).So I used Tinkercad to remix one.I split one in half, added some height to the center, and then added...

A simple build plate holder for the Anycubic Photon Mono printer that allows for the resin to drip off the plate a bit easier after a print is done.I used to use another one I found on the internet but its angle was too big so the taller prints were...

This lid ONLY WORKS with the Metal photon mono vat. Stock plastic vat will not work.</p><p>-V3 fix overall fit (needs a well-tuned printer so print fits properly)</p><p>-V2 fix corners and other small details</p><p>-Add no logo version</p><p>This...

It should reduce some resin fumes.The factory carbon filtration of Photon Mono SE doesn't work quite well. Two fans push fumes from build area through the activated carbon sponge to the bottom printer cavity and there large fan pushes air to the...

Made a vat cover/lid for the new Photon Mono 2 since i couldn't find one. Enjoy.There are two models: one titled VASE and one titled RIGID.The RIGID model is a thicker, more robust version. The two cylinders are knob covers and need to be glued on...

I've seen several Photon Mono adapters for Wash &amp; Cure, but I didn't feel like twisting and unscrewing the mount every time, and I also wanted to use the metal bracket that came with the kit rather than throw it away. The difference with my...

The factory Photon Mono SE advertises a "carbon filtration" system, but in reality it just consists of two really small fans (30mm x 30mm, similar size to the ones for cooling Raspberry Pi's) that pull air from the build area, through some activated...

Simple vat cover for the Anycubic Photo Mono M5s resin printer.

Mount for the Elegoo air purifiers for Photon Mono SE. Includes hangers for left and right side, can be used for anything you want to attach inside the printer. Allows side adjustment. Hangers are modeled for my printer, but depending on the...