photon mono x 3d models

<p>Spacer to replace your existing z-axis stopper. &nbsp; Shown in the images above is the stock spacer with a 2mm spacer that i initially used. &nbsp; I then made the component itself a single piece with that extension. ...&nbsp; The versions with 1...

This is a remix from Nicolasfromparis design. I wanted a cover that was all on piece instead of having to print 3 separate pieces and glue or screw them together. Remixed in Tinkercad and printed on Prusa MK3S. ...

2 part lid that clips together over the build plate and resin vat to help prevent UV light hardening the resin.

Potencial luz uv 100% Tempo de exposição normal 1s Tempo de exposição de base 30s

handle (Griffe) für die beiden anycubic Maschinen

I know there are several lid variants here on thingiverse, but all I've seen so far have to remove two bolts holding the VAT. My version just slides in place without need to unscrew it. It have two variants: left and right parts to glue together for...

Here the foot from the FEP Tank. ... I printed with ASA

This is a remix of https://www.thingiverse.com/thing:4754901 (I borrowed from the vat holder) I had 400mm 2020 extrusion left over so I designed a base and a funnel holder Base holds both stock spatulas and the Allen key There are two bases...

Coordinate system changed for Formware 3d

An alternate style build plate hanger that angles the plate for draining resin.

Remixed the VAT Stand https://www.thingiverse.com/thing:4674504 I have moved the funnel a bit and angled the receptacle for the tank a bit.

2 part lid that clips together over the build plate and resin vat to help prevent UV light hardening the resin.

This is a remix of https://www.thingiverse.com/thing:4754901 (I borrowed from the vat holder) I had 400mm 2020 extrusion left over so I designed a base and a funnel holder Base holds both stock spatulas and the Allen key There are two...

Inspired by: https://www.thingiverse.com/thing:3442165 The hole is a 8x8(7)mm square, should be big enough for most power cables, I used a bit of silicone to glue it to my mono X base and ensure its as airtight as possible and easy to remove later...

Wham Bam's magnetic flex plate is awesome but adds 2.6mm to the height of the build plate. Unfortunately, there isn't enough play in the build plate mount so the Z stepper grinds when I home the plate. One option is to print a 2.6mm spacer but I...

I didn't want to wait on a Wham Bam plate because I had prints that needed to get done so I ordered the Sovol plates from Amazon. They had a slightly different height recommendation (2.7mm) so I remixed this adapter in Tinkercad. ...Not only were they...

This is a proposal to increase the Z-stroke of the mono X photon printer. The first modification is to the Z-stroke detection system. Simply replace the original part with the part named "Z stroke end detection screw holder" and add a screw that...

I own a Mono X and Photon printer, so I draw a funnel that can hold all the two VAT, one at time, standing up to a resin bottle. ... The funnel can old inside a paper filter, if you cut it.

Anycubic Photon Mono X Resin Bottle Reservoir by jaseheuer Remixed for right and pre supported

... in place, and seal to the Vat. It uses the same philosophy as the Photon Mono X Vat. Watch the video below to see installation instructions. ... Installation Videohttps://youtu.be/mgY5Y1tznXI Mono X install (reference)https://youtu.be/tcCJFy_FcWE

Cable passthrough spacer for Photon Mono X. ...NOTE: this design is for the original lid for the Mono X, and WILL NOT work on the new lids, as the fit is too tight. Category: 3D Printer Parts

Cable passthrough spacer for Photon Mono X. ...NOTE: this design is for the original lid for the Mono X, and WILL NOT work on the new lids, as the fit is too tight.

Wenn ihr an euren Anycubic Photon Mono X eine Flexible Build Plate montiert, kommt ihr eventuell beim Leveln in die Mechanischen Grenzen an der Build Plate. Durch diese "unterlegscheibe" Schaltet eurer Z Endstop früher und Somit habt ihr genug Platz...

This drip hanger is designed for the Anycubic Photon Mono-X monochrome LCD resin printer. It is intended to be installed permanently (no need to put it on or take it off for printing or drip function). It allows one to print, then shift the build...

I couldn't find a tool stand for my Anycubic Photon Mono X 6K. So I made a simple tool stand. It's not the best looking stand lol but it works. I did print it to make sure everything that came with my printer would fit. I did put another slot for a...

These allow you to use "Workhorse Safety NIOSH P100" filters (The adapter seems a little different from the 3M adapter.) to assist in cleaning air for the Anycubic Photon Mono X. It all does limit the airflow, but ideally improves the air quality. ...

Photon Mono Vat Cover. ... Designed with Fusion 360

Anycubic Photon Mono VAT and Anycubic Photon Mono Frame SLA Printer - Rahmen SLA Drucker by Macyver1174 on Thingiverse: https://www.thingiverse.com/thing:4831934

Handle for the lid of an Anycubic Photon Mono Resin printer.

A dripper for the Photon mono. ...Designed to be permanently mounted behind the build plate position.