photon mono x vat 3d models

A simplified model of the Anycubic Photon Mono printer which will be released soon. Why? ...why not.

A custom-built container specifically designed to store and organize up to four Anycubic Photon resin printers safely and efficiently.

A storage rack for holding vats securely when not in use, designed with a slightly elevated floor to safeguard against FEP contact with the bottom and a taller stature that permits easy stacking without risking edge damage or collision.

No need to remove vat, just lift buildplate off, run 10-20 second print, and peel off printed sheet with remains stuck to it. Cured resin denser than uncured, sinks to bottom, loose trash sticks to print during exposure. ...Use this file to check LCD...

Spacer with cable hole for the Photon Mono inspired by ferro5's spacer for the Mono X. In case you want to put a heat source into the housing to keep the resin at nice 20-25° your cable will get into way. The spacer lifts the lid a bit and...

Replaces Photon Mono frame. ... Best results if layer height is .1-.2 mm, but still works with .3mm Works with original screws Tightens FEP film to allow for lower raised height (2-3mm)

anycubic photon mono legs. ...filament - bflex other accessories: https://www.thingiverse.com/thing:4923162 https://www.thingiverse.com/thing:4912979 https://www.thingiverse.com/thing:4912997 https://www.thingiverse.com/thing:4923146

Everyone with an Anycubic Photon Mono Resin Printer knows it: The Printer slides on a flat Surface. So I made these Feets. I printed them with PETG and attached self-adhesive rubber Feets. ... But I think, when you're able to print TPU or other...

Replacement for the top knob of the Anycubic Photon Mono X resin printer (also for Mono X2 and Mono X 6K). This is the knob that holds the platform in the Z axis arm. Also useful for any other M8 knob (but check the length of the screw needed). ... ...

I model this replica of the Anycubic Photon Printer, in order to print a miniature.Enjoy!

I built the PTC heater for my Mono but I needed a clean way to run the wires out to the power supply. This is a minimal riser that has a 1" gap in the back to allow wires to pass through. You can improve the seal by adding foam, batting, hot glue,...

... made by goyetus. ... It uses: 3 x m3 Nuts. 3 x m3 x 12 16 Magnet 5x5x5 Changed the back plate to use this fan: https://es.aliexpress.com/item/32810655513.html?channel=twinner Added the step file to modify the back as you want.

Build plate hang and drip bracket for Anycubic Photon Mono X. ...Allows you to hang the build plate at an angle and remove the parts as the excess resin drips back into the vat.

MODEL MADE FOR RESIN PRINTING WITH PHOTON MONO X AND ELEGOO SATURN DIVIDED INTO 2 PARTS INCLUDING SLICING FILES CREATED WITH LYCHEE INCLUDES BASE VBUCK

Parts A and B - if you can't print in one go

config that i use to print: Esun PLA+ layer height 0.21mm infil 25% tree support

Couldn't find a ready-to-go cover for my new SQ, so here you go.... not pretty, but it works. ... Yes, it does fit under the cover, too.

Anycubic Photon Mono drain bracket

This is a resin protection dam to protect the Anycubic Photon Mono X build platform screws/mounts in the center from being flooded with resin when being immersed into the VAT. Screws are cumbersome to clean, therefore I made this protection...

So now its only the base. Please use the following instead: ANYCUBIC Photon Mono X Clip On Heater Mount https://www.thingiverse.com/thing:5190198 Here are my other designs for the Anycubic Mono X 4K ANYCUBIC Photon Mono X Z-Axis Bumper Guard...

I made this replacement when my Z leveller on my Anycubic Photon Mono X broke - There is a Z offset spacer as well in case you need it to add height when installing a magnetic plate for your print bed or if you have a Z offset problem on your printer...

This is a two piece set to convert your original Anycubic Photon to the neck and baseplate adapter used in the photon mono. The photon mono uses an easy and in my opinion, more stable leveling and fixturing system of four set screws to lock the build...

For those who, like us, want to install a magnetic printing plate on their Anycubic Photon Mono X 6K, we provide the STL file for the Z limit sensor upgrade.We have installed Sovol magnetic printing plates on our 3 Anycubic Photon Mono X 6K and we...

I have created a spacers for the Anycubic Photon Mono X,for use with Wham Bam XTR line Flexible Build System at 3.8 mm tall You just need to print in resin or FDM and unscrew the interceptor arm from the machine and put the spacer between the build...

This is a full replacement for the plate that triggers the z endstop on the Anycubic Photon Mono X. It gives 2.5mm extra clearance under the build plate to accommodate a magnetic flex plate system. ...Easy print, and installs with the 2 screws that came...

... with v-buck base and stick. the package includes files already processed with slicer for PHOTON MONO X components have been positioned and optimized supports and emptying with 1mm thickness walls for other printers ask for your file ready to print

Hi, this is a modified version of the Anycubic Photon Vat Drip designed specifically to fit snugly onto the Photon's build plate. You're in luck because you can now easily print it on your very own Photon! ...Visit www.cadcamcenter.com for more...

Remixed from the vat stand from chrisgaw on ThingiverseA simple lid to put on your Anycubic Photons vat when it is not in the printer. Material or infill doesn't matter.

Inspired by: https://www.thingiverse.com/thing:3442165 The hole is a 8x8(7)mm square, should be big enough for most power cables, I used a bit of silicone to glue it to my mono X base and ensure its as airtight as possible and easy to remove later...

Hello, this is a cover system designed specifically for the Anycubic Photon Resin VAT. It's simple to install and can be placed directly on the vat if it's still installed. There are two versions available - one is the "full" version, which takes...