photon mono x build plate size 3d models

#Description# This is a longer z-stop flag for the Anycubic Photon Mono 4k with the newer version of the build plate arm which has a curved back where it mounts to the z-axis carriage. This z-stop flag is 4mm longer than the original metal piece,...

... for my printer. Эта модель - ремикс оригинальной модели https://www.thingiverse.com/thing:4611512. Исходная модель не совсем подходит к моему принтеру Anycubic Photon Mono 4k, так что пришлось перерисовать подходящую по размерам модель. ...

Build Plate for Tronxy X5S-400

This is a minimal extruding replacement for the back vent plate of the Anycubic Photon Mono SE 3D SLP printer with a 4" vent that can be used with a 4" Inch Inline Fan to vent the fumes. NOTE: This item hasn't been printed or tested yet, but the...

I've seen several Photon Mono adapters for Wash & Cure, but I didn't feel like twisting and unscrewing the mount every time, and I also wanted to use the metal bracket that came with the kit rather than throw it away. The difference with my adapter...

I was looking for a cover for my vat but only have my Anycubic Photon Mono 2 (no filament printer).All the lids I found were to large (even angled).So I used Tinkercad to remix one.I split one in half, added some height to the center, and then added...

I've been tinkering with ways to turn the Mia-X into the ultimate freestyle machine, so I flipped the build on its head by putting the motors and battery on top and stashing the rest of the electronics below.\r\n\r\nTo make this work, I began by...

This is a reinforced 3D printed frame for the Anycubic Photon Mono. ...I have created it when I've broken my original part, and I've figured out that it takes 40 days to get a new one :)

2.5mm z-axis separator for the anycubic photon mono 4k. ... The distance from the center of one circumference to the other is 8.5mm, the circumferences are 3.5mm Required if a flexible platform is to be used

anycubic photon mono resin vat lid other accessories: https://www.thingiverse.com/thing:4923162 https://www.thingiverse.com/thing:4912997 https://www.thingiverse.com/thing:4923159 https://www.thingiverse.com/thing:4923146

It should reduce some resin fumes.The factory carbon filtration of Photon Mono SE doesn't work quite well. Two fans push fumes from build area through the activated carbon sponge to the bottom printer cavity and there large fan pushes air to the...

... and print just fine. ...One corner points down for better drip control plus you don't even need to screw the build plate onto it because it's pointing upwards naturally. ...Printed it successfully without supports on an FDM machine without any issues.

You can print it on your photon mono, or on your traditional FDM printer :) Here is a simple to use and easy/quick to print holder for your Anycubic photon mono printer (4K in my case). All you have to do is remove the top knob, insert the holder,...

I've seen several Photon Mono adapters for Wash & Cure, but I didn't feel like twisting and unscrewing the mount every time, and I also wanted to use the metal bracket that came with the kit rather than throw it away. The difference with my...

Three precise dimensions define the full build volume of the Anycubic Photon: x=68.04, y=120.96, z=150. ...This information is valuable for anyone working with third-party 3D programs that require a visual guide to the photon's build space.

frame for standard bath photon

Made another cover for the Photon Mono because the others i found here on Thingiverse didn´t fit or it wont pass the screws which holds the vat in place when i tried to put the lid on. ... The distance from gap to gap on the lid is 15.2 cm.

This is a support for avoid to find a free place for the top cover. ...It simply hang to the printer itself. Printing: PLA, no spécial think. Here is the full desciption on Instructables : https://www.instructables.com/Photon-Mono-Top-Cover-Support/

Made another cover for the Photon Mono because the others i found here on Thingiverse didn´t fit or it wont pass the screws which holds the vat in place when i tried to put the lid on. ...The distance from gap to gap on the lid is 15.2 cm.

A side note - As I discovered when working on this project, each DVD sled has its unique design and different mounting locations, therefore, new parts will likely need to be made to accommodate your specific DVD drives, making these parts unlikely...

**https://www.printables.com/model/643200-anycubic-photon-mono-2-vat-cover** Made a vat cover/lid for the new *Photon Mono 2* since i couldn't find one. Enjoy. There are two models: one titled **VASE** and one titled **RIGID**. The **RIGID**...

Adapter for Photon Mono buildplate to mount on Anycubic Wash & Cure Station. Uses M6 screws, like the original. I used a height of 15mm instead of 12mm of the original mount on the Photon Mono. It makes everything a bit more stable and for me...

It simply hang to the printer itself.Printing: PLA, no spécial think.Here is the full desciption on Instructables : https://www.instructables.com/Photon-Mono-Top-Cover-Support/Print...

This lid also WORKS with Photon Mono -V3 fix overall fit (needs a well-tuned printer so print fits properly) -V2 fix corners and other small details -Add no logo version This resin vat lid keeps dust and other debris out of your resin tank and also...

Hello, I have created a screen cover with hinge for Anycubic Photon Mono 4K, so that at night the light from it does not annoy me when I sleep. The thickness is like this because I used black resin from Anycubic and it came out that in this...

Mount for the Elegoo air purifiers for Photon Mono SE. Includes hangers for left and right side, can be used for anything you want to attach inside the printer. Allows side adjustment. Hangers are modeled for my printer, but depending on the...

:-)__ ---------------------------------------------------------------- Inspiriert durch das Design "Anycubic Photon VAT Lid by KayIOA" habe ich einen Deckel für den Resinbehälter meines Anycubic Photon Mono entworfen ... mit einem Logo. Im ersten...

These are the very same components as the original blueprint, meticulously arranged upright on the build plate for seamless printing on the Aladdinbox SkyCube 3D printer. ... And check out my in-depth review of the SkyCube on YouTube:...

I liked the vat drip holder from this maker friend https://www.thingiverse.com/thing:3671334 but didn't have the best size depth for my mono x2 vat So I remixed this stand to it, with best size for mono X2 vat depth including a small cut extrude...

Hi!I made this for my Anycubic Photon Mono SE. This is the 4th iteration and can be printed at very high speed and still be functional. Settings I used:Line Width: 0.6mmLayer Height: 0.28mmSpeed: 120mm/sMaterial: PLASupports: No!You can use...