photon mono se 3d models
28352 3d models found related to photon mono se.
grabcad
Air vent box for ANYCUBIC PHOTON MONO SE using 3M Organic Vapor Cartridge 3311J-100-S1 and 12V Fan AV-F7530MB. You can swap the back panel of the printer with this. 12V can be drawn from the original fan cable inside of the printer. ...I added a DC/DC...
thingiverse
Anycubic Photon Mono SE SPACER - Wham Bam + Two Trees Flex Plate Spacer Part for Endstop after adding the new magnetic BUILT Plate Here 3 Parts for : - Wham Bam 3,00 mm - Two Trees 2,75 mm (Ali Express) - No Namer 2,50 mm Print in PETG You need to...
thingiverse
This support is permanent and therefore always ready to receive the tray. Very convenient when you already have a busy hand. Printing: PLA, no support, 100% cooling, no special precautions. ... Place it 5cm from the front.
thingiverse
A simple remix of Peppie23's 92x15mm rear vent adapter. The fan housing have been adjusted to 26mm as to easily house a standard 25mm thickness fan with some room to spare. The extra 1mm was added to accommodate for anti-vibration pads. ...Cuts down on...
prusaprinters
This support is permanent and therefore always ready to receive the tray.Very convenient when you already have a busy hand.Printing: PLA, no support, 100% cooling, no special precautions.Place it 5cm from the front.Print...
cults3d
Anycubic Photon Mono VAT and Anycubic Photon Mono Frame SLA Printer - Rahmen SLA Drucker by Macyver1174 on Thingiverse: https://www.thingiverse.com/thing:4831934
grabcad
Anycubic Photon Mono X printer external structural parts for projects and modifications.
thingiverse
A dripper for the Photon mono. ...Designed to be permanently mounted behind the build plate position.
thingiverse
Resin vat for Anycubic Photon Mono printer. Use 2.5x16mm screws with a flat head to assemble. ...
thingiverse
A simplified model of the Anycubic Photon Mono printer which will be released soon. Why? ...why not.
thingiverse
anycubic photon mono legs. ...filament - bflex other accessories: https://www.thingiverse.com/thing:4923162 https://www.thingiverse.com/thing:4912979 https://www.thingiverse.com/thing:4912997 https://www.thingiverse.com/thing:4923146
cults3d
Replaces Photon Mono frame. ... Best results if layer height is .1-.2 mm, but still works with .3mm Works with original screws Tightens FEP film to allow for lower raised height (2-3mm)
thingiverse
Spacer with cable hole for the Photon Mono inspired by ferro5's spacer for the Mono X. In case you want to put a heat source into the housing to keep the resin at nice 20-25° your cable will get into way. The spacer lifts the lid a bit and...
thingiverse
Everyone with an Anycubic Photon Mono Resin Printer knows it: The Printer slides on a flat Surface. So I made these Feets. I printed them with PETG and attached self-adhesive rubber Feets. ... But I think, when you're able to print TPU or other...
thingiverse
The Photon Mono X takes in air from the back of the device and exhausts out the bottom. So I created a system to take the exhaust from the bottom and exhaust it out the window. ... I used a Noctua 140 MM fan, but I would imagine any 140 MM fan would...
thingiverse
Here is a slution for every Photon mono X owner who keeps his printer in cold enviroment. A dedicated heating unit for keeping the resin and the print box at optimal printing temperature. There in no need for additional mounting screws you can use...
prusaprinters
I model this replica of the Anycubic Photon Printer, in order to print a miniature.Enjoy!
thingiverse
I built the PTC heater for my Mono but I needed a clean way to run the wires out to the power supply. This is a minimal riser that has a 1" gap in the back to allow wires to pass through. You can improve the seal by adding foam, batting, hot glue,...
thingiverse
This is a two piece set to convert your original Anycubic Photon to the neck and baseplate adapter used in the photon mono. The photon mono uses an easy and in my opinion, more stable leveling and fixturing system of four set screws to lock the build...
thingiverse
Remix of the Photon Zero Dripping Hook fitted to the buildplate of the Anycubic Photon Mono. ...easyfit
thingiverse
This is a support to maintain the Anycubic photon mono X VAT vertical.
grabcad
drainer Anycubic Photon mono xthere is no need to remove the screw because it passes without any problem