phospholipid 3d model

This model is cheaper than the usb c version and charges the Oculus Quest perfectly. This greatly improves your playing time and you could even charge the battery while using it. One design came close to what I liked, but was made for a different...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

I restarted from scratch and designed this model from those other inspirations. This version allows a 5015 fan to be installed without interference to the left or right gantry positions. I placed the fan above the slightly relocated CR Touch...

  I've been using the one in the picture for a few weeks and apart from not looking as pretty with the cam open, there's absolutely no difference in performance.I think I have allowed enough room to print this model with a .6mm nozzle but if you are...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

I first encountered the idea for this type of robot in a biomedical article, presented as a potential new candidate for exploring the human colon due to its simplicity and ability to navigate confined areas....

... - Schematics:  Goggly eyes are optional, but they improve performance and friendliness of the finished project. Modelled using tinkercad & blender. ...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_pattern_element_shape = 3 custom_right_port_length = 30 stencil_drawing =...

It can print without support, and if you have the workflow dialed in, it takes only about 30min per label from start to finish. You might get away with printing just the modell without the support stuff…. didn't try. Depending on your bridging it...

I use washers between the skate bearing and the mount to give a little clearance for the spool holder to turn (I could probably model in a little bump out instead of using washers). For adjustable friction, I've added a simple bail that attaches to...

### Bridge style cards (58mm x 88mm) * `codeandmake.com_Quick_Draw_Card_Dispenser_v1.0_58x88_Single_Open.stl` * `codeandmake.com_Quick_Draw_Card_Dispenser_v1.0_58x88_Single_Covered.stl` *...

...The design is optimized for the given print orientation - no need to rotate the STL model.You will also need two of the strain relief clips, which I have provided as a separate project.Assembly6 pieces of M3 nuts have to be pressed into the plastic.

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

This is a rather dramatic redesign and requires your printer to be able to comfortably print 55 degree overhangs though I would recommend facing the top of the model toward your fans for more efficient cooling of these overhangs. Please also note...

You have arrived at the "first three faces" - model one above. Next form a plane from the intersection points and the axis of rotation. Cut away from that plane. Voilà. Octahedron. NEW: Ten-sided added, and rounded and squished. Also blank. Simply...

Thread the wire through the lower cutout of this model and attach the new wire to the switch by pushing the two quick connectors onto the switch's terminals. ...Press the switch into its place in the case. </p><p>Cover the electronics (<a...

The assembly requires some M4 bolts and nuts, RGB strips, a hot glue gun, and tubing with a external diameter below 13mm (I have used 11mm). If you have any feedback, issues, or suggestions for future improvements please comment in the comment...

(You may be able to get away with shorter bolts but these were the only ones I had that would fit) I have included a thumb screw model to make it easier to open and close the cover without a wrench. You will need an M3 heat insert but I cannot stress...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

So far my failures are in optimizing the printer tuning to keep the model airtight. As stated in the Harvard paper, they printed a form and molded silicone for the soft actuators. I probably should do that too, but I am determined to work with FDM...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

READ BEFORE PRINTING!This is a non-commercial print, this means you are not allowed to sell files or prints of this model.______________________________________________________________________________________What is this?A modular tripod/handle...

The left adapter does require a small alteration which I did with a pair of side cutters (the ones that came with my Ender 3) (see pictures): - Unscrew the four screws at the bottom (be careful these strip easily) - Gently pull back the white tabs...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

Issues that I have with the design: In hand, the phone with my case (Model brand Apple silicone clone) on it fits snug. I can shake it vigorously upside-down and the phone doesn't fall out. However, After strapping it to the stem, the mount develops...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

Use "leveling_test.stl" model to test auto-level accuracy. I made some work tests of this firmware but there still could be bugs there, so use it on your own risk. Enjoy! :) Update 1: My Start and End G-codes in Cura working well with this...

Make your design on whatever modeling software (or download your design). Export as stl.</p><figure class="image image-style-align-center image_resized" style="width:40.37%;"><img...