phone tripod mount 3d models

... This is necessary to mate with the standard tripod screw CAUTION: This mount is intended to hold a smartphone on a stationary tripod. I wouldn't trust it on something in motion. For a moving tripod, consider using an action camera mount instead.

Inspired by cswaim's clamping method, this universal phone mount features a wider clamping surface and tightening nuts for added security. Printable in 3.5-4 hours on standard settings without support, optimized for PLA. To assemble, attach two 4"...

I've created a thing to mount a mobile phone on a tripod. You will need a small hair tie or household rubber band to join the pieces together. Assembly: I first pulled the hair tie through the hole of the upper part. Then I slowly pushed the...

... pattern if you're printing with Cura. Post-printing, I was thrilled to see how well my universal tripod mount worked with the Osmo and my Samsung Galaxy S5 with Otterbox Commuter case. ...It's been a game-changer for my mobile filmmaking setup!

Mount your phone to an Arca-Swiss compatible tripod I combined the extended version of JakeJake's phone mount with the Arca Swiss plate by JohnClark The slider and knob are unmodified from the original design Print Settings Rafts: No Supports: No...

... to ensure they fit together seamlessly. When it comes to attaching this mount to a tripod, there's a recessed area designed specifically for a 1/4" nut that can be epoxied into place - alternatively, you can download a custom nut from my page.

So I decided to dust off an old project that was collecting dust, and turn it into a adjustable tripod mount that will fit any of my phones, no matter what case is on them. At the moment, it uses a rubber band to hold everything in place, but it...

Ensure that the holders are properly aligned: the tripod mount features two angled holders, while the stand side boasts two flat holders. Consult the assembled STL photo for visual reference. To secure a 1/4"-20 nut in the end cap hole for use with...

... iPhone 5 or SE without a case and an iPhone 6 with a thin case. To avoid damaging it, be careful not to overtighten the plastic bolt, which can easily snap off. Additionally, you'll need to attach a 1/4" - 20 nut to your tripod for proper mounting.

This project started cause I did not want to hold my cell phone by hand recording Class lectures and so it evolved into an ajustable cell phone mount. I have printed this item out on a 3D printer and it works great. Hardware such as nuts and all...

Completely redesigned this simple little tripod mount, ditching unnecessary elements like supports and skirts. Easy to print and assemble, it gets the job done with minimal fuss! One rubber band does the trick. Print Settings: Printer Brand: ...

My expandable cellphone tripod mount broke on me so this is my attempt at making a replacement for it. I'm sure there are better ones out there but this one suits me for now. I just took all the parts out and transferred them over to the newly...

Customized Version of the Popular Thingiverse Design: Customized Holder for Mobile Phones Created with Our Customizer App at http://www.thingiverse.com/apps/customizer/run?thing_id=73622 Using These Settings: * Base Cutout Size: 0.8 Units * Base...

A custom phone dock, specifically designed for users who want a versatile and durable solution to hold their phones. Created with Thingiverse's Customizer tool. ... To use this design, you'll need to adjust the following options: - Holder width: 10...

... ...https://www.thingiverse.com/apps/customizer/run?thing_id=73622 Options Used: * Holder Height: Set to 20 * Base Inset: Set to 4.1 * Base Cutout Width: Set to 0.8 * Base Width: Set to 43.25 * Phone Width: Set to 9.2 * Holder Width: Set to 10

Customized Version: http://www.thingiverse.com/apps/customizer/run?thing_id=73622 Instructions Using the following settings: Holder Height is 20 units Base Cutout Diameter is set at .8 inches Phone Holder Width is adjusted to fit standard phones up...

http://www.thingiverse.com/apps/customizer/run?thing_id=73622 Instructions Using the following settings: Holder width: 5 inches Phone width: 7.6 inches Base inset: 4.1 inches Holder height: 7 inches Base height: 50 inches Base width: 30 inches Base...

Customize to fit your needs with the options below: Choose your phone width: 13.5 cm Select your holder width: 10 cm Set base inset: 4.1 mm Set base cutout depth: 0.8 mm Determine base width: 43.25 cm Choose holder height: 20 mm Select base height:...

http://www.thingiverse.com/apps/customizer/run?thing_id=73622 Instructions Using the following options: phone_width = 13 base_inset = .1 holder_height = 20 base_cutout = 0.8 base_inset = 0.1 holder_width = 10 phone_width = 13 base_inset = 0.1...

Using the customization settings below: Holder Width: 7 inches Phone Width: 7.6 inches Holder Height: 15 inches Base Cutout: Yes, create a hole for easy base assembly Base Inset: 4.1 inches to snugly fit on flat surfaces Base Width: 30.4 inches for...

http://www.thingiverse.com/apps/customizer/run?thing_id=73622 Getting Started Guide Using these options to craft your perfect phone stand: Phone width is set at 9.3 units. Holder height stands tall at 20 units. Base cutout provides clearance of 0.8...

* **Phone Width:** Our stand can accommodate a phone width of up to 13mm, making it versatile and easy to use with different phone sizes. * **Base Inset:** To avoid damage to surfaces or the base itself, we've set this value to 4.1mm by default. ...*...

Using the options available: - Holder width is set to 10 units - The base height of the holder measures 9.1 units - Base width measures 43.25 units - Phone width fits snugly at 13 units - Height of the holder is 20 units - A small cutout is placed...

Here Are the Options to Customize Your Holder: • Holder Width: Set it at 10 • Base Height: Keep it Low with a Height of 3 • Base Width: Make it Roomy at 35 • Phone Width: Precision Crafted for Phones as Wide as 8.97 • Holder Height: Make a Statement...

... with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=73622 Instructions Using the following options: holder_width = 10 base_height = 9.1 base_width = 43.25 holder_height = 20 phone_width = 9.3 base_inset = 4.1 base_cutout = 0.8

... with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=73622 Instructions Using the following options: base_inset = 4.1 base_cutout = 0.8 holder_height = 20 phone_width = 12.3 base_width = 43.25 holder_width = 10 base_height = 9.1

... Made with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=73622 Using the following options: Base width: 43.25mm Base cutout: 0.8mm Holder height: 20mm Base inset: 4.1mm Base height: 9.1mm Holder width: 10mm Phone width: 10.5mm

... with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=73622 Instructions Using the following options: holder_height = 20 base_inset = 4.1 phone_width = 10.2 holder_width = 10 base_height = 9.1 base_cutout = 0.8 base_width = 43.25

https://www.thingiverse.com/apps/customizer/run?thing_id=73622 Design Notes Design Parameters Using the following options: Base Width - 43.25 Phone Width - 7 Base Inset - 4.1 Base Cutout Diameter - 0.8 Holder Width - 10 Base Height - 15 Holder Height...

... Customizer! ... You are now viewing this model using the following options: Base Height = 9.1 inches Base Width = 43.25 inches Holder Height = 20 inches Base Inset = 4.1 inches Holder Width = 10 inches Phone Width = 9.5 inches Base Cutout = 0.8 inch