phone tripod holder 3d models

Phone mount for standard tripod mount. ... Mount- Support needed Top clip- support needed Nut- no support

You can sit any phone on on the tripod with this mount.

I've got an unorthodox clamp+ballhead setup that needs a compact phone holder, so I decided to design my own. Simple, slim, and adjustable - this is what I aimed for. Standard "tripod screw" ensures it can be attached anywhere. The design is 100%...

... plate. The locking component of this design fits both tripods I own, which I assumed was a standard size, possibly not. Adjusting the separation between holders for your specific phone is likely the only measurement you'll need to modify.

Custom Tripod mount for cell phone. This was made for my galaxy S6 with printed case to fit snug in the holder horizontally. Uses 10-32 screw and nut to hold bracket to base. ... 3/11/19 Added a threaded bottomed version to fit 1/4 20 SAE Thread.

This secures a Galaxy S7 phone, equipped with a standard case, firmly onto a sturdy SunPak tripod setup.

Universal tripod for mobile phone. Supports cell phones with width between 35mm and 75mm. ...Link to assembly video.https://youtu.be/BwaIZ9CT5ok

This is a universal phone holder. It attaches securely to any universal tripod or camera screw. I designed this model based on another one found on Thingiverse, but it has the added feature of a hole mount at the bottom. To print successfully, make...

Hello, I designed very strong and very practical foldable tripod for phone. This tripod its much stronger and well made than anything else what i saw. Its very easy to print and also very easy to assembly. I didnt want to make plastic screws because...

This is a secure phone holder designed to be set on a table top or threaded on to a tripod mount. It comes in three separately printable pieces. (See the colored photo.) The green and pink parts thread into each other to set to the width of the...

These screws only need to be slightly loosened to remove the legs for transportation.Sliding Ball Socket with Lock: A socket that slides on the central pole, allowing a phone holder (from the PlasticClamp project) to be attached. This socket can...

I've got an unorthodox clamp+ballhead setup that's begging for a compact phone holder, so I'm designing my own. It needs to be simple, slim and adjustable - check! Standard "tripod screw" so it can attach anywhere - done! 100% printable with no...

Just slide the extension onto the pole of the tripod and place the phone between the hooks, insert from the top and the bottom hook and the side hooks will keep it in place so it does not fall out. ... For it to work, change the size by 1120% ...

But you can give your own phone dimensions in the FreeCAD file and the holder will be scaled to your phone.To assemble you push the catches in the clamp’s holes and pull a rubber band over them.The print file is set for PETG but you can make your own...

You can utilize this mount to securely position your phone or tablet on a tripod, perfect for capturing high-quality video footage or taking long exposure photos.

Mount your phone firmly onto a sturdy tripod, utilizing hooks designed to secure a rubber band that grips the device tightly yet remains removable with ease.

When making a customized version, avoid naming it as "My Customized Phone Tripod Mount" and consider publishing with '[Phone Model] on [Tripod Model] Tripod Mount". About a hundred customized versions have been made so far. The pictured mount was 3D...

The phone holder works with rubber bands tensioning both parts together. I decided on using this method for simplicity and print time. I work on this for just a few minutes in Rhino 7 and needed it fast so i could mess with printed screws. The...

(In the design there is a hole for another M4 nut in the bottom part which is supposed to be glued in place and should serve as a mounting point if you dont have a standard tripod mounting nut like I had laying around) SUPPORTED PHONES: You can use...

(In the design there is a hole for another M4 nut in the bottom part which is supposed to be glued in place and should serve as a mounting point if you dont have a standard tripod mounting nut like I had laying around) SUPPORTED PHONES: You can use...

(Make sure your popsocket is centered on your phone for it to stay level, it won't work if mounted near the edge.) I used a few supports on both pieces and it printed very easy. If you need to make the tripod tighter, simply add a small piece of...

I was looking for a phone tripod stand and there was nothing usable for a case with a popsocket so I remixed this. (Make sure your popsocket is centered on your phone for it to stay level, it won't work if mounted near the edge.) I used a few...

This is a mount for using a phone on a manfrotto tripod, originally meant for a camera. The mount is adjustable and is able to accommodate phones of different width. Rubber bands do need to be used to keep the phone from slipping out of the mount.

Needed a way to put my phone on my tripod, remixed the object and added a groove to fit my phone. ...Fits iPhone 13 Pro Max nicely, works decent with XS Max (I don't know about other phones, but you can use a small piece of plastic as a wedge).

... body. New parts are continually added and updated to improve the design and capabilities of the tripod. Enjoy this new creation. ... Check out my other tripod here: https://www.thingiverse.com/thing:3064866 Follow me on Instagram: fra3d.085

... if it will fit every brand perfectly. ... My tripod had a cheap phone adapter that snapped easily, prompting me to design this as a replacement. ... You'll want to print the nut with a "Horizontal expansion" of -0.4mm so it's easier to turn smoothly.

This is a universal adapter that fits on any standard tripod, enabling you to safely attach your smartphone to it. Simply insert the threaded end of the screws into the unthreaded holes and screw the component with the holes onto your tripod first.

Fits to mini tripod and has a slot for phone to sit in, nothing more magic than that. Printed in two halves for speed/no supports. ...The two shells snap together.

ENGLISH: This is a simple smartphone tripod, designed for my Samsung J5 but it can work with other smartphones. If you want the .fcstd file to adapt to your phone just leave a comment. ... Use M4 nuts and screws.

Mobile phone clamp features a built-in 1/4 inch tripod socket. The adjustable grip spans 2.7 to 2.9 inches wide. ... A makeshift clamp is formed using a spring taken from a clothespin.