phone scope mount 3d models

No supports needed, assuming your printer is capable of a decent amount of bridging.Use M3x8mm screws to mount the TFT to the holder, and the holder to the lid, and the clamp that holds the DC connector in place. Use M3 screws of an appropriate...

After having a blade guard break on mine while it was in my backpack during some pretty typical traveling I figured it was time to just print up a case.The main idea behind this case is to support the drone by its corners and provide rigid top and...

Future, I might make a bracket so you can hang hose and/or mount the hose's high pressure nozzle like you would with a store bought shower head with hose extension. I also might experiment with gasket making and upload some printable templates for...

Before the final installation of the bearing to its full down position I rolled an o-ring ***(3.5mm thick x 30mm ID x 36.5mm OD) *** all the way down the steering tube, over the tiny fork-crown and had it come to a rest under the fork-crown and well...

Another option for feeding filament to a printer directly from this box is to mount the box above the printer and drill holes in the bottom. There is room to do this, and I intend to do so eventually. The "humidity ring" part is to hold a common...

However, I'm leaving it up in case somebody has better ideas such as mounting springs/elastics to take some of the strain and balance out some of the weight. Without such an improvement however, you are likely, like I have, to burn out a number of...

Peel back adhesive strip from LED strip and mount both strips. Insert second MALE connector into the other hole from the outside (strip connecting wires will block it from coming in too far). Test your led strips to make sure they light up. Now...

Next, press motor further into the motor mount such that the shaft is half way through staircase. Press arm onto motor shaft via the access hole such that the motor shaft flat and arm flat mate, and the arm is inside the large rectangular hole in...

STEP-File is included, just in case you need to adopt the mounting holes. Sometimes, the IR sensor doesn't recognize the flag depending on the material used. To overcome this issue, I've painted the top part with a black marker. Testing Did some...

Use a bit of silicone grease on the nozzle.Connect the cone with a line to the bottom of the bottle or alternatively to the middle of the parachute or drone parachute.Make a neat package of the main parachute in the top part.Put the drone parachute...

Just use a hot glue gun to mount the electronics in the base. IF YOU ARE HAPPY WITH THAT, A LITTLE DONATION WILL BE VERY NICE <3 https://www.paypal.com/donate/?hosted_button_id=5F525DYM8GXK4 If you want to do a remix or changes to the design,...

The KV-1’s strengths included armour that was stubbornly impenetrable by any tank-mounted weapon then in service, had good firepower and decent mobility on soft ground from the use of its wide tracks. Despite its vast superiority, the KV-1...

#Features & BOM: 18650 battery https://www.amazon.com/gp/product/B01C4GFVN8 #or 2500 MAH Lipo - use the cover without 18650 holder https://www.amazon.com/YDL-2500mAh-battery-Rechargeable-Connector/dp/B07BTY599F #or 5000mah battery and the 3mm extra...

We combined the display engine nozzles from the Titan file and mounted them on to a display block. During our searches for information on the Dyna-Soar we found a really nice logo/shield. We decided to add that to the display stand in a raised relief...

- Replace the stock extruder mount by the filament sensor holder This work is based on the original Superfly extruder design by Mustcode https://www.thingiverse.com/thing:4841682...

I recommend to enable Ironing in the slicer for best light transmission FMLED-4 LED-v3.stl FMLED-7 LED-v3.stl PowerLED-3LED-v2.stl Large PETG Parts Recommended 0.2mm layer height &amp; 0.4mm nozzle: LCD-Arm-v2-printable.stl...

I have already seen a couple of things that I'd like to change, like putting the rudder hinge in the same side as the servo and mounting the aileron servos on the top of the wing instead underneath it (i don't know if I'll change that one) Of course...

To find back which rotor is associated with which ring, how to mount its ring and which one is it, there is 3 indications on each rotor: - on the ring side (left) a mark show the tooth on which the 'A' may normally be placed, - on the large side...

All parts are meant to be cross-compatible between kits for your kitbashing enjoyment.The contents of this kit are provided in three zip files:kelvin-blender-files.zip – The Blender source files used to generate the ship and part STL...

I created this print so that I don't need to babysit the grill on long cooks - just set and forget.Additional materials required (available at hardware stores or online):1mm thick aluminium or stainless steel sheet30mm x 50mm aluminium rectangle...

35mm.&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;Assembly instructions for a shelf:&nbsp;&nbsp;&nbsp;There are several ways to mount the connectors. I found this one the easiest.</p><p>Press the nuts and the screw into the parts for the foot.<br>Both parts are...

It has a built-in heatsink/heatblock.&nbsp;The biggest compaint I have seen about them is that they are not securely mounted to the Pi. They only attach via the GPIO pins, there's no provision for a standoff or a screw. So I've made a STABILIZER part...

SMD means "surface mount device" which means it's tiny, and 1206 implies the soldering area is 1.2mm x 0.6 mm. However, please don't faint, even an amateur as myself can solder this easily, just take a good look at my photographs before starting. The...

If you want to thanks or support:PayPal Yandex money Benefits: Allows you to reduce the length of retracts and K-factor in Linear Advance, significantly reducing printing time Improved material flow control results in improved printing quality of...

Monoceres Mk 2 The MK 2 Monoceres replaces the single nacelle with two top mounted versions. Zip Files Combined ship files are included in this project individually. The individual parts files and blender files used to create the STL files are...

### Parts | **Part** | **Description** | |-------------------------------------|---------------------------------------| | T2-cannon-mount.stl | Front hull cannons. | | T2-nacelle-port.stl | Port warp nacelle. ...

# Additional Notes The project box I used was too small to fit both voltage regulators, the Pi Pico and the ESC, so I just mounted the ESC to the top of the box since it's waterproof. It's probably best for it to get some airflow anyway. I read a...

Optionally you can set the desktop preferences: uncheck wastebasket and mounted disks, and increase system font to about 24 pixels. In File Manager settings, select Open files with single click, Don't ask options on launch exec, and Don't show...

Lotharius comes on a 32mm base, the Rotting Bloodwing comes on a 130mm Base, and his Blood Reavers come on a 25mm base for the foot version, and 75x42mm Oval bases for the Mounted version :) Kai'zhar Lotharius Sanguinaar, The First Ruler of the...

This will make the mounts stronger and at the same time retain the model's mobility.Here is a list of .stl files that have been added as a second version of the legs:1. 1_leg_1_R_V22. 2_foot_connector_V2_x2 (need to print twice)3. 3_leg_2_R_V24. You...